Bedienungsanleitung Grohe 36371 F-DIGITAL DELUXE (Seite 89 von 92) (Alle Sprachen)

759534

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

External interface

Via the external interface the Bluetooth® adapter can be

rebooted or resetted. It is adapted as a break contact, which

can be used with conventional nc (normally closed) type

switches or push buttons.

1. Turn the entire system free of voltage.

2. Remove Bypass (C), see fold-out page I.

3. Connect switch or push button with cable 47 868 000

(special accessorie) to the external interface

(max. 16.4 ft [5m]).

4. Supply the entire system with voltage.

If the external interface is not used, the bridging contact

must remain plugged in!

Pairing

Pairing means the first coupling between two Bluetooth®

devices. This requires a proper executed installation. For an

already active Bluetooth® connection between a terminal

device and the Bluetooth® adapter no pairing is possible.

1. Activate Bluetooth® on device.

2. Select xxx Grohe SPA from Bluetooth® list.

xxxx is the 4-digit number (PIN number) which will be

displayed.

3. Enter PIN number and confirm.

4. Connection will established automatically.

5. The LED (A) on the adapter flashes 1x blue for a short time

when connection is quite correct.

The PIN number is unique for each adapter and is additionally

documented with a sticker on the backside. These are the last

four digits of the serial number. The PIN number can not be

changed!

When successfully paired, the PIN is no longer required when

a new connection attempt. When connected and activated the

App LED on the adapter lights up blue continuously. A

maximum of 8 devices can be paired. When logging a 9th

device the most rarely used one will be deleted from the list.

XXXX

Operation of the reset button (A) and Visualization by status LED (B)

Functions

Function Visualization

Operation takes place LED lights permanently blue

Reboot of the adapter LED lights up red for 3 sec.

Reset of the adapter LED lights up red, off, red, blue, red

Ready for operation LED off

Modul is supplied with voltage LED lights up red for 1 sec.

Permanent press of button, or

bridging contact removed

LED flashes red

Function Describtion

Changing the device Device will be logged out (connection closed/inactive).

After 10sec. the new device can be logged in.

Prioritization of connections It will be ensured that the operation can take place only with a single device

at any time.

Visibility of the Bluetooth® adapter The Bluetooth® adapter is always visible.

Reboot the Bluetooth® adapter

(Entire system turns off)

Press the button shortly (less than 3 sec.):

- Connection will be interrupted

- Bluetooth® adapter reboots

- System shuts down (Music, light (max. 60sec. delay), steam)

Reset of the Bluetooth® adapter

(Entire system turns off)

Press and hold the button (between 10 and 20sec.):

- Connection will be interrupted

- Pairing list will be cleared

- Bluetooth® adapter reboots

- System shuts down (Music, light (max. 60sec. delay), steam)

Data transfer As soon as a device is connected, the system can be operated using the

Grohe App.

Audio stream As soon as a device is connected, an audio stream can be sent to the

system by the Grohe App.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Grohe 36371 F-DIGITAL DELUXE Seite 89

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info