Bedienungsanleitung Grohe 38778 Tectron (Seite 10 von 16) (Deutsch, Englisch)

759441

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Making settings

Disassemble plastic plate, see Fig. [30a].

Disassemble metal plate, see Fig. [30b].

Registering a radio transmitter

A maximum of 30 radio transmitters may be registered.

When registering a radio transmitter, make sure that no other

radio transmitters are being operated at the same time.

1. Activate registration mode by pressing button (C2);

(C1) flashes once in confirmation, see Fig. [31].

2. Within 30 seconds, press the transmitter button (Z) for

triggering flushing.

3. (C1) flashes three times to confirm correct receipt of a radio

signal.

4. The coding of the particular radio transmitter is stored and

the radio transmitter is then registered. Registration mode is

terminated.

Control reverts to normal mode.

Pressing the radio transmitter again following successful

registration (in normal mode) triggers flushing.

Further radio transmitters are registered as described above.

Setting the flow volume for manual actuation (cistern B)

1. Small button (only possible with dual-flush actuation):

Setting is via the blue float (S3). For a setting dimension of

90mm, the low flow volume is 3 litres, see Fig. [32].

2. Large button:

- For a flow volume of 6 litres, residual flow slider (S4)

must be pushed fully upwards.

- For a flow volume of 9 litres, residual flow slider (S4)

must be pushed fully downwards.

Note: The flow volume for radio triggering must be set to the

same flow volume, see Setting the flow volume for radio

triggering.

Setting the flow volume for radio triggering

1. Activate registration mode by pressing the button;

(C1) flashes once in confirmation.

2. Press and hold the button again in registration mode.

(C1) flashes rapidly in confirmation.

This flashing signal is interrupted for 1 second

after 5 seconds.

3. Release the button within 2 seconds. Flush duration

adjustment mode is activated.

4. The flow volume is selected by pressing the button

- button pressed for first time (within 2 seconds):

3 flashing signals = flow volume 3 litres

- button pressed for second time (within 2 seconds):

4 flashing signals = flow volume 4 litres

- button pressed for third time (within 2 seconds):

5 flashing signals = flow volume 5 litres

- button pressed for fourth time (within 2 seconds):

6 flashing signals = flow volume 6 litres (factory setting)

- button pressed for fifth time (within 2 seconds):

7 flashing signals = flow volume 6 litres (cistern A)

flow volume 9 litres (cistern B)

After the group with 7 flashing signals, the routine starts from

the beginning.

5. The flow volume is selected by refraining from pressing the

button within 2 seconds after the desired flow volume is

signalled.

6. One flush is performed at the set volume with the signal

flashing once more.

7. The flow volume can be changed within 20 seconds of

flushing (if necessary) by pressing the button again. The

selected flush setting is stored if the button is not pressed

again within 20 seconds of flushing.

Control reverts to normal mode.

Switching 72-hour flush on and off

(factory setting: switched on)

1. Activate registration mode by pressing the button.

(C1) flashes once in confirmation.

2. Press and hold the button again in registration mode.

(C1) flashes rapidly in confirmation.

The signal is interrupted for 1 second after 5 seconds.

3. Keep the button pressed. After 5 seconds, the LED

extinguishes for 2 seconds. The LED then illuminates

continuously.

4. Release the button.

5. Switch the 72-hour flush on or off by pressing the button

again within the following 2 seconds.

- 4 short flashing signals after the button is pressed =

72-hour flush is switched on.

- 2 long flashing signals after the button is pressed =

72-hour flush is switched off.

6. Each press of the button switches between the two states.

7. If the button is not pressed again within 10 seconds, control

reverts to normal mode.

Deleting a radio transmitter

1. Press button (C2) (C1 flashes once briefly in confirmation)

and hold for 8 seconds.

2. Holding the button continuously for 8 seconds deletes all

registered radio transmitters; (C1) flashes once briefly in

confirmation.

Control reverts to normal mode.

Maintenance

Inspect and clean all components and replace if necessary.

For maintenance of the cistern parts, see cistern

instructions.

Replacing the transformer, see fold-out page IV

1. Switch off voltage supply, see Fig. [33].

2. Disconnect extension cable (L) from upper part (A2) and

disengage existing upper part of transformer (A2), see

Fig. [34].

3. Locate and engage new upper part.

4. Connect new upper part (A2) to extension cable (L).

5. Switch on voltage supply, see Fig. [33] (setting mode is

activated for 3 minutes).

Shut off water supply.

Replacing the servo motor, see fold-out page IV

1. Disassemble plastic plate, see Fig. [30a].

Disassemble metal plate, see Fig. [30b].

2. Detach lift rod (P) from lever (V3), see Fig. [35a] or [35b].

3. Remove bracket with servo motor (V).

4. Disconnect plug connection from electronic module (C) to

extension cable (L) and to servo motor (V), see Fig. [36].

5. Calibrate new servo motor, see Calibrating the servo

motor.

6. Install new servo motor, see Installing the servo motor.

7. Install wall plate, see Installing the plate.

Grohe 38778 Tectron Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info