Bedienungsanleitung Grohe Grohtherm 1000 Cosmopolitan (Seite 4 von 6) (Alle Sprachen)

626490

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

GBGB

Application

Thermostat mixers are designed for hot water supply via

pressurised storage heaters and, utilised in this way, provide

the best temperature accuracy. With sufficient power output

(from 18 kW or 250 kcal/min), electric or gas instantaneous

heaters are also suitable.

Thermostats cannot be used in conjunction with

non-pressurised storage heaters (displacement water

heaters).

All thermostats are adjusted in the factory at a flow pressure

of 3 bar on both sides.

Should temperature deviations occur on account of special

installation conditions, the thermostat must be adapted to local

conditions (see Adjusting).

Specifications

Minimum flow pressure without

downstream resistances 0.5 bar

Minimum flow pressure with

downstream resistances 1 bar

Max. operating pressure 10 bar

Recommended flow pressure 1 - 5 bar

Test pressure 16 bar

Flow rate at 3 bar flow pressure approx. 13 l/min

Max. water temperature at hot water supply 80 °C

Recommended max. flow temperature (energy saving) 60 °C

Hot water temperature at supply connection min. 2 °C higher

than mixed water temperature

Cold water connection right

Hot water connection left

Minimum flow rate = 5 l/min

If static pressure exceeds 5 bar, a pressure reducing valve

must be fitted.

Installation

Flush piping system prior and after installation of fitting

thoroughly (Consider EN 806)!

Screw-mount the mixer, see fold-out page II, Fig. [1].

Refer to the dimensional drawings on fold-out page I.

The projection can be increased by 20mm with an extension,

see Replacement Parts, fold-out page I, Prod. no. 07 130.

For better fixing into dry-lined walls a mounting frame

can be used (see Replacement Parts, fold-out page I,

Prod. no.: 18 153).

With pillar union 18 121 or 18 066 (see Replacement Parts,

fold-out page I) fitting distance 150mm can be switched to

180mm bathtub rim.

Adjustment

Temperature adjustment, see Figs. [2] and [3].

1. Open the shut-off valve and check the temperature of the

water with a thermometer, see Fig. [2].

2. Lever out cap (A), see Fig. [3].

3. Remove screw (B).

4. Detach temperature control handle (C).

5. Turn regulating nut (D) until the water temperature has

reached 38 °C.

Install in reverse order.

Check operation of automatic diverter (E), see fold-out

page III, Fig. [4].

Flow is diverted automatically from shower outlet to bath inlet

when the fitting is closed.

Prevention of frost damage

When the domestic water system is drained, thermostat

mixers must be drained separately, since non-return valves

are installed in the hot and cold water connections. For this

purpose, the mixer must be removed from the wall.

Maintenance

Inspect and clean all parts, replace if necessary and lubricate

with special valve grease.

Shut off the hot and cold water supply.

I. Non-return valve (F) or (G), see fold-out page III, Fig. [5].

• Remove connection nipple (H) by turning clockwise (left-hand

thread) using a 12mm allen key.

• Remove connection nipple (I) by turning clockwise (left-hand

thread) using a 15mm allen key.

Install in reverse order.

II. Thermostatic compact cartridge (J), see fold-out page III,

Fig. [6].

• Loosen screw ring (K) using a 34mm tool.

• If necessary, lever out thermostatic compact cartridge (J) via

recess (J1).

• Remove screw ring (K).

Install in reverse order.

Observe the correct installation position of the

thermostatic compact cartridge (J), see detail (J2).

Readjustment is necessary after every maintenance operation

on the thermostatic compact cartridge (see Adjusting).

III. Ceramic headpart (L), see fold-out page III, Fig. [7].

IV. Unscrew and clean flow straightener (47 908),

see fold-out page I.

Replacement Parts, see fold-out page I

( * = special accessories).

Care

Dear Customer,

We want to ensure that you get long-lasting satisfaction and

pleasure from your GROHE fitting. Therefore, please read the

following care instructions because damage to the surface and

underlying material resulting from improper treatment is not

covered by warranty.

Do not use any abrasive sponges or scouring agents for

cleaning. We also advise you not to use cleaning agents

containing solvent or acid, limescale removers, household

vinegar and cleaning agents with acetic acid in them. They are

aggressive to the surface - and will leave your fitting dull and

scratched. As the formulations of commercially available

cleaning agents frequently change, we cannot guarantee they

will provide the gentle care our fitting deserves.

Clean the fitting with a little soap and a moist cloth only, then

simply rinse off and wipe dry. You can avoid lime spots by

drying the fitting each time it is used. If lime deposits do occur,

remove them with GrohClean, our environment-friendly

cleaning liquid. GrohClean is specially formulated to clean the

surface of our fittings gently. GrohClean is available from your

supplier.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Grohe Grohtherm 1000 Cosmopolitan Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Grohe Grohtherm 1000 Cosmopolitan

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info