Bedienungsanleitung Ground zero GZHA 4150 X (Seite 12 von 48) (Deutsch)

66440

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Hydrogen amplifiers

Due to their state- of- the- art technology and high efficiency, these amplifiers help your system to provide an

impressive sound experience. The modern circuit technology of the power supply and the signal processing allows

achieving maximum performance levels from the provided power.

Tools and materials you need

• Screwdriver

• Electric drill, 3 mm / 0.12” carbide drill bit

• Mounting screws

• Power wire min. 16 mm² / 5 AWG

• Ground wire min. 16 mm² / 5 AWG

• Speaker wire min. 2 x 1,5 mm² / 15 AWG

Please note!

• As a precaution it is advisable to disconnect the vehicle’s battery before making connection

to the +12 Volts supply wiring (see owner’s manual of your car for further information).

• Please use great caution drilling your trunk. Your gas tank and brake lines can be damaged by

puncturing with your drill bit – this could cause damage or failure of your cars operating systems.

• Never pass wires over sharp angles. It is recommended to buffer the power supply of the amplifier

with an capacitor min. 1 Farad to guarantee a stable operation voltage.

WARNING !

High powered audio systems in a vehicle are capable of generating "Live Concert" levels of sound pressure.

Continued exposure to excessively high volume sound levels may cause hearing loss or damage. Also, operation

of a motor vehicle while listening to audio equipment at high volume levels may impair your ability to hear

external sounds such as; horns, warning signals, or emergency vehicles, thus constituting to a potential traffic

hazard. In the interest of safety, Consumer Electronics recommends listening at lower volume levels while driving.

Planning your system

Before beginning the installation, consider the following:

a. If you plan to expand your system by adding other components sometime in the future, ensure

adequate space is left, and cooling requirements are met.

b. If your radio / source is equipped with pre-amp outputs, it is possible to utilize them to drive the

amplifier and connecting (amplifier) to the 2 rear speakers.

Mounting your amplifier

a. Select a suitable location that is convenient for mounting, is accessible for wiring

and has ample room for air circulation and cooling.

b. Use the amplifier as a template to mark the mounting holes, remove the amplifier

Warning

Chose a mounting position where all eclectic wires are protected from being damaged by sharp edges, heat or

other conditions. +12Volt DC electrical connections must be fused on the battery side. Make sure your radio and

all other devices will be turned off while connection your system.

If you need to replace the power fuse, replace it only with a fuse identical to that supplied with the system. Using

a fuse of different type or rating may result in damage to this system which isn’t covered by the warranty.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ground zero GZHA 4150 X Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ground zero GZHA 4150 X

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info