Bedienungsanleitung Ground zero GZPA 1.4000D (Seite 8 von 18) (Deutsch)

505538

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

TOOLS AND MATERIALS YOU NEED:

• SCREWDRIVER;ELECTRIC DRILL;1/8 CARBIDE DRILL BIT;

• USE 2AWG POWER WIRE (min. 35 mm²)

• GROUND YOUR AMPLIFIER ONE METER CLOSE TO INSTALATION LOCATION

• USE 12 AWG SPEAKER WIRE OR HEAVIER FROM YOUR AMPLIFIER TO YOUR SPEAKERS

• LOOK FOR BURS IN THE PATH OF YOUR WIRES AND FILE THEM FLAT TO AVOID PUNCTURE

• USE 16 AWG WIRE FOR REMOTE TRIGGER

NOTE ALL WIRE GAUGES ARE BASED ON STRANDED WIRE WITH POLARITY INDICATORS ON TWO

WIRE CONFIGURATIONS

PLEASE USE GREAT CAUTION DRILLING YOUR TRUNK, YOUR GAS TANK AND BRAKE LINES CAN BE DAMAGED

BY PUNCTURING WITH YOUR DRILL BIT: THIS COULD CAUSE DAMAGE OR FAILURE OF YOUR CARS OPERATING

SYSTEMS:

INTRODUCTION

Amplifiers provide high-performance sound reinforcement for you mobile audio equipment. It’s versatility enables

compatibility with optional equalizer, frequency dividing network crossovers, and other audio processors in a

customized system.

The Multi-Mode bridging capabilities allow flexibility in hosting several different speaker configurations.

To achieve optimum performance , it is highly recommend that you read this owners manual before beginning the

installation

WARNING

High powered audio systems in a vehicle are capable of generating „Live Concert“ high level of

sound pressure. Continued exposure to excessively high volume sound levels may cause hearing

loss or damage. Also, operation of a motor vehicle while listening to audio equipment at high

volume levels may impair your ability to hear external sound such as; horns, warning signals, or

emergency vehicles, thus constituting to a potential traffic hazard. For safety reasons we

recommends listening at lower volume levels while driving.

MOUNTING YOUR AMPLIFIER:

The mounting position of your amplifier will have a great effect on its ability to dissipate the heat generated

during normal operation. It has an ample heat sink for heat dissipation, and is also designed with a thermal shut

–down(for heat protection) circuit, DO NOT enclose the amplifier in a small box or cover it .

Temperatures in car trunks have been measured as high as 175’F(80 Celsius) in the summer time , since the

thermal shut-down point for the amplifier is 185’F( 85 Celsius) it is easy to see that it must be mounted for

maximum cooling capability. To achieve maximum advantage of convection air flow in a enclosed trunk, mount

the amplifier in a vertical position, on a vertical surface.

Floor mounting under the seat is usually satisfactory as long as there is at least 1 inch (2 cm) above the

amplifier’s fins for ventilation.

a) selected a suitable location that is convenient for mounting, is accessible for wiring and has enough

room for air circulation and cooling.

b) Use the amplifier as a template to mark the mounting holes, remove the amplifier and drill 4 hols,

use extreme caution, inspect underneath surface before drilling.

c) Secure the amplifier by using screws.

CAUTION:

AS A PRECAUTION; IT IS ADVISABLE TO DISCONNECT THE VEHICLE’S BATTERY BEFORE MAKING CONNECTION

TO THE +12 VOLTS SUPPLY WIRING (see owner’s manual of your car for further in formation !)

min. 35mm² (thicker if planning for additional amplifiers) wire is recommended both the power and grounds. Both

types are available at most Mobile audio dealers or installation shops.

1.) GROUND: To vehicle Chassis

To avoid ignition noise caused by ground loops, it is necessary that the amplifiers be grounded to a clean, bare

metal surface of the vehicles chassis.

NOTE: GROUND WIRE SHOLD NOT BE EXTENDED MORE THAN 3 FT.(1 Meter) min. 35mm²

2.) +12 Volt (Fused) Constant power: To Battery (+)

Due to the power requirements of the amplifier, this connection should be made directly to the positive (+)

terminal of battery. For safety reasons, install an in-line fuse holder (not included) as close to the battery positive

(+) terminal as possible with a rating not exceeding value of fuses in amp.

3.) Remote Turn-On Input: to power antenna output of Car Stereo

This amplifier is turned ”ON” remotely when the vehicle’s stereo is turned ”ON”.

NOTE:

IF YOUR RADIO DOES NOT HAVE +12 VOLT OUTPUT LEAD ;THE “REM” TERMINAL ON THE AMPLIFIER CAN BE

CONNECTED TO VEHICLE’S ACCESSORY CIRCUIT THAT IS LIVE WHEN THE KEY IS”ON

”.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ground zero GZPA 1.4000D Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info