Bedienungsanleitung Ground zero GZPA 1.8K-18V (Seite 8 von 18) (Deutsch)

505535

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

Tools and materials you need

• Screwdriver

• Electric drill 1/8 carbide drill bit

• Mounting screws

• Use 0 AWG power wire (min. 50 mm²)

• Use 0 AWG ground wire (min. 50 mm²)

• Use 11 AWG speaker cable (min. 4 mm²)

Caution!

• Please use great caution drilling your trunk, your gas tank and brake lines can be damaged by

puncturing with your drillbit – this could cause damage or failure of your cars operating systems.

• As a precaution it is advisable to disconnect the vehicle’s battery before making connection to the

+12 Volts supply wiring (see owner’s manual of your car for further information!).

• 0 AWG / min. 50 mm² (thicker if planning for additional amplifiers) wire is recommended both the

power and grounds. Both types are available at most Mobile audio dealers or installation shops.

• Please consider the enormous power consumption (up to 900A) of these amps when designing the

setup. We strongly recommend to install one or better more additionally batteries. Too little power

from the battery / alternator may cause defects

WARNING

High powered audio systems in a vehicle are capable of generating „Live Concert“ high level of

sound pressure. Continued exposure to excessively high volume sound levels may cause hearing

loss or damage. Also, operation of a motor vehicle while listening to audio equipment at high

volume levels may impair your ability to hear external sound such as; horns, warning signals, or

emergency vehicles, thus constituting to a potential traffic hazard. For safety reasons we

recommends listening at lower volume levels while driving.

Planning your system

a) select a suitable location that is convenient for mounting, is accessible for wiring and has enough

room for air circulation and cooling.

b) If your radio is equipped with preamplifier outputs (RCA), it is advisable to use them.

Mounting your amplifier

• Select a suitable location that is convenient for mounting, is accessible for wiring and has ample

room for air circulation and cooling.

• Use the amplifier a template to mark the mounting holes, remote the amplifier and drill 6 holes (use

extreme caution, inspect underneath surface before drilling!)

• Secure the amplifier using the screws provided

Connections

1.) GROUND: To vehicle Chassis

To avoid ignition noise caused by ground loops, it is necessary that the amplifiers be grounded to a clean, bare

metal surface of the vehicles chassis.

NOTE: GROUND WIRE SHOLD NOT BE EXTENDED MORE THAN 3 FT.(1 Meter) min. 0 AWG / 50mm²

2.) +12 Volt (Fused) Constant power: To Battery (+)

Due to the power requirements of the amplifier, this connection should be made directly to the positive (+)

terminal of battery. For safety reasons, install an in-line fuse holder (not included) as close to the battery positive

(+) terminal as possible with a rating not exceeding value of fuses in amp.

3.) Remote Turn-On Input: to power antenna output of car stereo

This amplifier is turned ”ON” remotely when the vehicle’s stereo is turned ”ON”.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ground zero GZPA 1.8K-18V Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info