Bedienungsanleitung Ground zero GZTA 5125X (Seite 11 von 40) (Deutsch)

505567

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Controls and functions – GZTA 5125X

Controls and functions

1 Speaker terminals For connection of the speakers

Power terminals

GND -> Ground connection

REM -> Remote antenna terminal

BATT -> +12 Volt

3 Satus indication

GREEN

–

RED – Error

4 Cinch inputs

Terminal for connection of the RCA wires.

To avoid failure, please use high quality RCA wires.

5 Input level controlle

With this controller you can adjust the input sensitivity.

6 Mode switch

djust the crossover for the chosen utilization.

LPF – Only bass frequencies (below 40Hz - 4000Hz) (G

ZTA 5120X

Channel 5: 40Hz – 250Hz) will be reproduced.

FULL – All frequencies will be reproduced.

HPF – Only middle and high frequencies (

GZTA 5125X

: over 5 Hz –

4000 Hz /

GZTA 5120X

: over 40 Hz – 4000 Hz ) will be reproduced.

GZTA 5125X:

At LPF adjustment, also the Highpass (Subsonic) is activated.

This equals a Bandpass filter of 5 – 4000 Hz.

7 Low pass controller

Only frequencies from 40 Hz to 4000 Hz (

GZTA 5120X

Channel 5: 40

Hz – 250 Hz) will be reproduced (depending on the LPF filter controller

position). Set the filter switch to „LOW“ (“LP”) position. Adjust the

variable LPF frequency to the desired frequency using the controller.

High Pass controller

(Subsonic)

Set the filter switch to „HIGH“ position.

Adjust the variable HPF crossover frequency to the desired frequency

using the controller. All frequency between 5 and 4000 Hz (

GZTA

5120X

: 40 Hz – 4000 Hz) will be reproduced.

9 Filter controller

Depeding on the mode switch position, High- or Lowpassfilter can be

adjusted in a range from 40 Hz – 4000 Hz with this controller.

Subsonic controller

(GZTA 5120X Channel 5)

For adjusting the subsonic filter in a range from 10 Hz to 50 Hz.

11 Input mode switch

This switch allows you to choose the number of used cinch inputs.

6 channels of

GZTA 5125X

can be operated with a 2- channel Cinch

cable.

You can chose if the 5

channel of

GZTA 5120X

should be operated

with Cinch input 5/6 or the summation of input 1/2/3/4.

12 Phase Shift controller

This controller allows you to fit the subwoofer channel of

GZTA 5120X

in-phase to the front system.

14 Remote control input For connection of the bass remote control.

Input Mode GZTA 5125X

2: This adjustment allows you to operate all 6 channels using the Cinch- Input Ch 1 and Ch 2. This is

recommended for active operation of a 3 way front system. For using this possibility, connect for example the

front cinch output of your headunit to the Ch 1/2 of the amplifier.

4: The channels 5 and 6 will be operated using the summarized signal from channel 1/2 and 3/4.

This mode is suggestive if channel 5 and 6 are only used as subwoofer channels.

For using this possibility, connect for example the front and rear cinch output of your headunit to the Ch 1/2 and

Ch 3/4 of the amplifier.

6: This adjustment allows you to operate every channel with an own signal. Using this possibility, every channel

can be adjusted by your head unit or processor separately.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ground zero GZTA 5125X Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info