Bedienungsanleitung Ground zero GZUA 4125SQ (Seite 7 von 21) (Deutsch)

505517

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

Introduction

Amplifiers provide high-performance sound reinforcement for your mobile audio

equipment. It’s versatility enables compatability with optional Equalizer, Frequency

Dividing Network Crossovers and other audio processors in a customized system.

The Multi-Mode bridging capabilitis allow felxibility in hosting several differnet

speaker configurations.

To achieve optimum performance , it is highly recommend that you read this Owners

manual before the installation.

Tools and materials you need

• Screwdriver

• Electric drill, 3mm

• Mounting screws

• Power wire min. 20mm²

• Groud wire min 20mm²

• Speaker wire min. 2 x 1,5 mm²

Attention

• As a precaution; it is advisable to disconnect the vehicle’s battery before making connection to the

+12 Volts supply wiring (see owner’s manual of your car for further information!)

• Do not drill holes into the tank, the brake pipe, wires or other important parts of the vehicle

• Never pass wires over sharp angles. It is reccomended to buffer the power supply of the amplifier

with an capacitor min. 1 Farad.

WARNING

High powered audio systems in a vehicle are capable of generating „Live Concert“ high levels of

sound pressure, Continued exposure to excessively high volume sound levels may cause hearing

loss or damage. Also, operation of a motor vehicle while listening to audio equipment at high

volume levels may impair your ability to hear external sound such as; horns, warning signals,or

emergency vehicles, thus constituting to a potential traffic hazard. In the interest of safetay,

Consumer Electronics recommends listening at lower volume levels while driving.

Planning your System

Before beginning the installation, consider the following:

a) If you plan to expand your system by adding other components sometime in the future, ensure da equate

space is left, and cooling requirements are met.

b)If your radio/source is equipped with Pre-Amp outputs, it is recomended to utilize them to drive the amplifier

c) Are your components matched? The peak power rating of your speakers must be greater than the

Amplifiers.They also must be 2-8 Ohms impedance (This information os normally printed on the speaker magnet)

Consider both the length of your leads, and routing when chosing the mounting location. Pre-Amp input jacks

require a length of high quality shielded male to male RCA patch cord.

Mounting your amplifier

a) Select a suitable location that is convenient for mounting, accessible for wiring and has enough

room for air circulation and cooling.

b) Use the amplifier as a template to mark the mounting holes, remove the amplifier and drill 4 holes,

use extreme caution, inspect underneath surface before drilling.

Wiring connection

Attention!

mind. 20mm² wires are necessary for power connection

1.) Ground: Ground connection should be passed directly to the car body as short as possible (max. 1m)

2.) +12 Volt: Power connection should be passed directly to the battery. Please pay attention on a correct fuse

protection of the installation with an Inline device with a max. wire length to the battery of 30 cm.

3.) Remote turn on: This connection is getting connected with the remote control line of the radio. It is used for

turning on and off the amplifier.

Warning

Investigate the layout of you automobile thoroughly before drilling or cutting any holes. Take care when you work

near the thanks, lines, or hydraulic lines, and electrical wiring. Don’t mount this system so that wire connections

are unprotected or are subject to pinching or damage from nearby objects.

The +12 Volt DC power wire must be fused at the battery positive terminal connection. Before making or breaking

power connections at this system power terminals, disconnect the +12 Volt wire at the battery end.

Confirm your radio / cassette player and / or other equip, mount is turned off while connecting the input jacks

and speaker terminals.

If you need to replace the power fuse, replace it only with a fuse identical to that supplied with the system. Using

a fuse of different type or rating may result in damage to this system which isn’t covered by the warranty.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ground zero GZUA 4125SQ Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info