789277
42
Zoom out
Zoom in
Vorherige Seite
1/55
Nächste Seite
42
Error messages and troubleshooting
You can see by the error indicator light (h) what is wrong
if the robot lawnmower has stopped.
Indicator light Faults
Lights up red 1) The robot lawnmower has been
lifted
2) The robot lawnmower is stuck
3) Skirt error
Flashes red 4) Boundary cable signal error
Lights up blue 5) Battery error
Flashes blue 6) Abnormal battery temperature
7) Charging error
8) PCB overheating
9) The robot lawnmower has
rolled over
10) The robot lawnmower is
overloaded
11) There is an obstruction on the
boundary cable
The errors are described below.
1) The robot lawnmower has been lifted
The robot lawnmower will report an error if the lift
sensors are continuously activated for 10 seconds.
Press the OK button to re-start the robot lawnmower.
If the error occurs repeatedly, you should check the
work area.
Remove any obstacles of over 100 mm, as these may
cause the robot lawnmower to roll over.
Use a regular lawnmower to cut grass that is taller than
60 mm.
2) The robot lawnmower is stuck
The robot lawnmower reports an error if the obstacle
sensors are activated more than 5 times in one minute.
Press the OK button to re-start the robot lawnmower.
If the error occurs repeatedly, investigate whether the
boundary cable is laid out correctly, as the error often
occurs in places that are too narrow or too cramped for
the robot lawnmower to move forward after changing
direction.
Also check whether there are obstacles such as
branches, etc. that may be restricting the robot
lawnmowers freedom of movement.
3) Skirt error
There are four magnets in the robot lawnmower’s skirt.
If any metal comes between the magnets and the skirt,
the robot lawnmower may report an error.
Remove any pieces of metal.
Press the OK button to re-start the robot lawnmower.
4) Boundary cable signal error
The robot lawnmower will rotate a number of times,
stop and report an error if it goes outside the work area
or if there is an error with the boundary cable.
Check that the robot lawnmower is within the work
area and then check the indicator light on the charging
station:
Indicator light Indicates
O The charging station is not plugged
in.
Lights up
green (symbol
1)
The boundary cable is connected
correctly, the robot lawnmower
is ready and the battery is fully
charged..
Flashes green
(symbol 2+3)
There is a break in the boundary
cable.
The ends of the boundary cable are
connected the wrong way around on
the charging station.
Correct the error.
Lights up red
(symbol 4)
The battery is charging.
Flashes green
and red
alternately
Maintenance charging of battery
(trickle charging).
4 3 2 1
42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

grouw-17940---s600

Suche zurücksetzen

  • Roboter verliert die Programmierung nach der Reinigung und Neustart. Eingereicht am 4-7-2024 16:07

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Grouw 17940 - S600 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info