545191
71
Zoom out
Zoom in
Vorherige Seite
1/83
Nächste Seite
71
ENGLISH
»KB Frequency (MHz)«: Enter the user
band frequency assigned to the user
band with »1...0« buttons.
»LNB Selection«: If more than one
satellites are used in the current SCR
system, select »1/2« to»2/2« for the
satellite corresponding to the relevant
positions using »
<
« or »
>
« buttons.
Notes:
7
Use installation equipment supported /
suggested by your Multiswitch.
7
Other users / receivers connected to the
system may be affected if the specified user
band number and frequency is changed
during installation.
7
User band and User band frequency is
specified on the Multiswitch used; and
each user / receiver uses a specified user
band and user band frequency.
7
With SCR satellite system, auto search by
several users / receivers at the same time
may cause problems.
»22 KHz«: Depending on the LNB type,
22 kHz audio is selected. For a univer-
sal LNB, this option is set to »Auto« and
cannot be changed.
»DISEqC mode« and »LNB selection«:
depending on the type of antenna used,
use »
<
« or »
>
« select the option »Off«,
»DiSEqC 1.0« or »DiSEqC 1.1«.
»Off«: for a satellite system with only
one antenna.
» DiSEqC 1.0«: allows up to four satel-
lites to be received simultaneously.
Under »LNB selection«, use »
<
« or
»
>
« to select the option »1/4«, »2/4«,
»3/4« or »4/4«.
» DiSEqC 1.1«: allows up to 16 satel-
lites to be received simultaneously.
Under »LNB selection«, use »
<
« or
»
>
« to select the option »1/16« to
»16/16«.
5 Press »MENU« to end the setting.
SPECIAL SETTINGS
----------------------------------------------------------------------------------------------------------
Settings for motorised antennas
(DiSEqC 1.2)
Your television set supports motorised satellite
systems in compliance with DiSEqC 1.2. This
function allows the satellite antenna to be oper-
ated via the television set.
1 Open the menu with »MENU«.
2 Select the line »SOURCE SETUP« with »
V
«
or »
Λ
« and press
»OK«
to confirm.
The »SOURCE SETUP« menu appears.
3 Select the line »DiSEqC 1.2« with »
V
«
or »
Λ
«. Select the option »On« with »
<
«
or »
>
«
The line »User Mode« is active.
Note:
7
Additional operations are explained in the
following sections.
71

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Grundig 46 VLE 8270 CP wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Grundig 46 VLE 8270 CP

Grundig 46 VLE 8270 CP Bedienungsanleitung - Deutsch - 87 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info