570183
7
Zoom out
Zoom in
Vorherige Seite
1/11
Nächste Seite
7
ENGLISH
Connecting the power adapter
Note:
7
Check that the mains voltage on the power
adapter corresponds to your local mains
supply.
If this is not the case, contact your spe-
cialist dealer.
1 Connect the single plug of the power adapter
into the »DC IN 12 V« socket.
2 Connect the power adapter into the wall sock-
et.
Caution:
7
The device is connected to the mains with
the power cord. Pull out the power adapter
if you want to completely disconnect the de-
vice from the mains.
7
Make sure the power adapter is easily ac-
cessible during operation and not hindered
by other objects.
Activate the remote control
battery
1 Remove protection film from the battery com-
partment.
– The remote control is now functional.
Change remote control
battery (Type CR 2025)
Note:
7
If your device no longer responds to the
remote control commands, the battery may
be dead. It is imperative that dead batteries
be removed. We do not assume liability for
damage caused by leaked batteries.
Caution:
7
Danger of explosion if battery is incorrectly
replaced.
Replace only with the same or equivalent
type.
1 Hold the remote control with the back side fac-
ing up.
2 Unscrew safety bolt of the battery holder and
remove the battery holder.
CONNECTION AND PREPARATION
____________________
3 Insert the battery with the positive pole facing
upwards.
4 Push battery holder into the remote control until
it clicks into place.
5 Screw in the safety bolt.
Charging external device
Note:
7
Switch the device off before you connect
external devices.
1 Place the external device carefully on the
»
Micro USB
« charging plug;
or
pull out the charging plug carefully and con-
nect it to the micro USB socket of the external
device.
Note:
7
Pull out the holder sufficiently far so that the
external device can be stored.
2 When the external device is charged, pull out
the plug, pull on the charging plug gently and
the cable retracts automatically.
Connecting external devices
Note:
7
Switch the device off before you connect
external devices.
1 Use a standard audio adapter to connect
the audio outputs of the external device
to the »AUX IN« 3.5 mm) socket of the
GSD 300.
7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Grundig GSD 300 BLUEBEAT wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Grundig GSD 300 BLUEBEAT

Grundig GSD 300 BLUEBEAT Bedienungsanleitung - Deutsch - 11 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info