Bedienungsanleitung Grundig GTN 27250MG (Seite 39 von 160) (Deutsch)

712283

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

ENGLISH

Beveling the Shoe (Fig. E)

To Bevel the Shoe

1. Remove the dust extraction accessories if they are mounted

to the tool as the tool will not bevel if they are attached.

Refer to Dust Extractionsection.

2. Unlock the shoe by pulling the shoe bevel lever

8

theside.

3. Slide the shoe

7

forward to release it from the 0° positive

stopposition.

NOTE: The shoe can be beveled to the left or to the right

at a maximum of 45° in either direction. There are visible

detents at 15° and 30°.

4. Once the desired bevel angle is achieved, lock the shoe in

position:

a. For 0° and 45° bevel angles, slide the shoe back and lock

the shoe by moving the bevel lever back under the body

of the jig saw.

b. For all angles between 0° and 45°, lock with bevel

leveronly.

Cutting Action—Orbital or Straight (Fig. F)

This jig saw is equipped with four cutting actions, three orbital

and one straight. Orbital action has a more aggressive blade

motion and is designed for cutting in soft materials like wood

or plastic. Orbital action provides a faster cut, but with a less

smooth cut across the material. In orbital action, the blade

moves forward during the cutting stroke in addition to the up

and downmotion.

NOTE: Metal or hardwoods should never be cut in orbitalaction.

To adjust the cutting action, move the orbital action lever

6

between the four cutting positions: 0, 1, 2, and 3. Position 0 is

straight cutting. Positions 1, 2, and 3 are orbital cutting. The

aggressiveness of the cut increase as the lever is adjusted from

one to three, with three being the most aggressivecut.

Dust Blower (Fig. G)

The dust blower

19

helps clear the cutting area of debris

created from theblade.

Dust Extraction (Fig. A, H)



WARNING: Dust can be hazardous to health. Always

work with a dust extractor. Always observe the national

regulations for work with dust emittingtools.

The dust extraction chute in combination with the dust

extraction shroud helps extract dust from the workpiece surface,

when connected to a suitable dust extractionsystem.

NOTE: The tool will not bevel if the dust extraction accessories

are attached to thetool.

1. Place the dust extraction shroud

15

onto the finger

guard

5

(Fig. A) until it clicks intoplace.

2. Slide the dust chute

16 from the back of the tool until

it snaps into the dust shroud. Be sure the adapter end is

facingup.

3. To connect a vacuum to the dust chute

16

, place a

DeWALT

AirLock (DWV9000), found on all full size

DeWALT

vacuum

hoses, over the dust collection port, and twist the collar

to lock it into place. The dust chute will also fit a standard

35mmconnector.

Removeable Anti-Scratch Shoe Cover (Fig. I)

The anti-scratch shoe cover

17

should be used when cutting

surfaces that scratch easily, such as laminate, veneer orpaint.

To attach anti-scratch shoe cover

17

, place the front of the

shoe

7

into the front of the anti-scratch shoe cover and lower

the jig saw. The anti-scratch shoe cover will click securely onto

the rear of theshoe.

To remove anti-scratch shoe cover, grasp the anti-scratch shoe

cover from the bottom; holding onto the two rear tabs

18

remove the anti-scratch shoecover.

Anti-Splinter Insert (Fig. I, J)

NOTE: Do not use the anti-splinter insert with the flush

cuttingbladeDT2074.

The anti-splinter insert

20

should be used when trying to

minimize tear-out, especially when cutting veneer, laminate, or

finished surfaces, such as paint. The anti-splinter insert should

be installed into the anti-scratch shoe cover

17

. If the no-mar

cover is not used, install anti-splinter insert into shoe

7

Setting the Electronic Sawing Speed

(Fig. A, K)

DCS334

To preset the sawing speed, turn the speed control dial

3

to the

desired level. The higher the number on the speed control dial,

the higher the sawing speed. The sawing speed varies with the

pressure exerted on the variable speed trigger

1

, but will not

exceed the speed that is set by the speed control dial

3

. The

required setting depends on the thickness and kind ofmaterial.

NOTE: Use high speeds for sawing soft materials such aswood.

DCS335

The speed control dial

3

can be used for advance setting of the

required range ofspeed.

1. Turn the electronic control dial to the required level. The

DCS335 will turn on at that speed when the on/off switch is

moved to the ON position. The required setting depends on

the thickness and kind ofmaterial.

NOTE: Use high speeds for sawing soft materials such aswood.

Worklights

The worklights are located on either side of the blade. To turn

on the worklight, depress the trigger (DCS334) or switch on the

on/off switch (DCS335). Worklights will remain on 20 seconds

after the tool is turned on, or as long as your cut lasts.

NOTE: The worklights are for lighting the immediate work

surface and are not intended to be used as aflashlight.

Prior to Operation

Make sure your battery pack is (fully)charged.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Grundig GTN 27250MG Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info