Bedienungsanleitung Grundig GWD38400C (Seite 40 von 48) (Englisch)

769843

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

40 /EN Washer-Dryer / User Manual

Machine directly discharges the water it takes in.

• The drain hose might be at an inappropriate height. >>>

Connect the water drain hose as described in the user manual.

No water can be seen in the machine during

washing.

• Water level cannot be seen outside the machine. This is not a

failure.

Loading door cannot be opened.

• Door lock might be enabled because of the water level in the

machine. >>>

Drain the water by running the Pump or Spin

programme.

• Machine might be heating the water or at the spinning

step.>>>

Wait until the programme is complete.

• The loading door might be jammed due to the pressure it is

exposed to. >>>

Hold the grip, push and pull the loading door

to free it from the pressure and open it.

• The loading door will not open if there is no power. >>>

open the loading door, open the pump filter cap and pull down

the emergency handle positioned at the rear side of the said

cap. See “Loading door lock”

Washing takes longer than specified in the user

manual.(*)

• Water pressure might be low. >>>

Since the amount of the

water has decreased, the machine will wait until it takes

adequate water to avoid poor washing quality. Therefore, the

washing time extends.

• Voltage might be low. >>>

If the supply voltage is low, the

washing time is extended to prevent poor washing quality.

• Inlet temperature of water might be too low. >>>

The time

required to heat up the water extends in cold seasons. Also,

washing time can be extended to avoid poor washing results.

• The number of rinsing cycles and/or the amount of rinsing

water might have increased. >>>

When a better rinsing

performance is needed, the machine increases the amount of

rinsing water, and adds another rinsing cycle, if necessary.

• Excessive foam might have formed due to use of too much

detergent, and the automatic foam absorption system might

have been activated. >>>

Use the recommended amount of

detergent.

Programme time does not countdown. (On models

with display) (*)

• The timer may stop during water intake. >>>

The timer

indicator will not count down until the machine takes in an

adequate amount of water. When the amount of the water

taken in decreases, the machine will wait until it takes in

enough water to avoid poor washing results. Timer indicator

will resume countdown after this.

• The timer indicator might stop during heating. >>>

The timer

indicator will not count down until the machine reaches the

selected temperature.

• The timer indicator might stop during spinning. >>>

The

automatic unbalanced load detection system might have been

activated due to uneven distribution of the laundry in the drum.

Programme time does not countdown. (*)

• The laundry in the machine might be unbalanced. >>>

The

automatic unbalanced load detection system might have been

activated due to uneven distribution of the laundry in the drum.

Machine does not switch to spinning step. (*)

• The laundry in the machine might be unbalanced. >>>

The

automatic unbalanced load detection system might have been

activated due to uneven distribution of the laundry in the drum.

• The machine cannot spin if the water in it is not drained

completely. >>>

Check the filter and the drain hose.

• Excessive foam might have formed due to use of too much

detergent, and the automatic foam absorption system might

have been activated. >>>

Use the recommended amount of

detergent.

Washing performance is poor: Clothes are going grey.(**)

• Insufficient amount of detergent might have been used over

a long period of time. >>>

Use the recommended amount of

detergent according to water hardness and the laundry.

• Washing might have been performed at low temperatures for a

long time. >>>

Select the proper temperature for the laundry

to be washed.

• Hard water and insufficient amount of detergent. >>>

Using

hard water together with insufficient amount of detergent

might cause dirt accumulation and greying on laundry in

time. It is difficult to eliminate greying once it happens. Use

the recommended amount of detergent appropriate for water

hardness and the laundry.

• Excessive amount of detergent might have been used. >>>

Use the recommended amount of detergent appropriate for

water hardness and the laundry.

Washing performance is poor: Stains persist or the

laundry is not whitened. (**)

• Insufficient amount of detergent might have been used. >>> Use

recommended amount of detergent appropriate for the laundry.

• Machine might have been overloaded. >>>

Do not overload the

machine. Load the machine with the amounts recommended in

the "Programme and consumption table".

• Wrong programme and temperature might have been selected.

>>>

Select the right programme and temperature for the

laundry to be washed.

• Wrong type of detergent might have been used. >>>

Use

original detergent appropriate for the machine.

• Detergent might have been put in the wrong compartment.

>>> Put the detergent in the correct compartment. Do not mix

the bleaching agent and the detergent with each other.

Washing performance is poor: Oily stains appeared

on the laundry. (**)

• The drum might not have been cleaned regularly. >>>

Clean

the drum regularly. To do this, please see. 6.2.

Washing performance is poor: Clothes smell bad. (**)

• Washing at low temperatures and/or with short programmes

for a long time will cause smell and bacteria in the drum. >>>

Leave the detergent drawer and loading door of the machine

ajar after every washing cycle. Thus, a humid environment

favorable for bacteria cannot occur in the machine.

Grundig GWD38400C Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info