Bedienungsanleitung Grundig GWN 48430 CW (Seite 41 von 52) (Englisch)

574811

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

41 / EN

Washing Machine / User‘s Manual

8 Troubleshooting

Programme cannot be started or selected.

• Washing machine has switched to self protection mode due to a supply problem (line voltage, water

pressure, etc.). >>> Press and hold Start / Pause button for 3 seconds to reset the machine to factory

settings. (See "Cancelling the programme")

Water in the machine.

• Some water might have remained in the product due to the quality control processes in the production.

>>> This is not a failure; water is not harmful to the machine.

There is water leaking from the bottom of the machine.

• Likely problems with hoses or the pump filter. >>> Be sure the seals of the water inlet hoses are securely

fitted. Attach the hose to the tap tightly.

• Pump filter might not be closed fully. >>> Check if the pump filter is completely closed.

Machine does not fill with water.

• Tap is turned off. >>> Open the taps.

• Water inlet hose is bent. >>> Correct the hose.

• Water inlet filter is clogged. >>> Clean the filter.

• The loading door is ajar. >>> Close the loading door.

Machine does not drain water.

• Water drain hose might be clogged or twisted. >>> Clean or flatten the hose.

• Pump filter is clogged. >>> Clean the pump filter.

Machine vibrates or makes noise.

• Machine might be standing unbalanced. >>> Adjust the feet to level the machine.

• A hard substance might have entered into the pump filter. >>> Clean the pump filter.

• Transportation safety bolts are not removed. >>> Remove the transportation safety bolts.

• Laundry quantity in the machine might be too little. >>> Add more laundry to the machine.

• Machine might be overloaded with laundry. >>> Take out some of the laundry from the machine or

distribute the load by hand to balance it homogenously in the machine.

• Machine might be leaning on a rigid item. >>> Check if the machine is not leaning on anything.

Machine stopped shortly after the programme started.

• Machine might have stopped temporarily due to low voltage. >>> It will resume running when the

voltage restores to the normal level.

Machine directly discharges the water it takes in.

• Draining hose might not be at adequate height. >>> Connect the water draining hose as described in the

operation manual.

No water can be seen in the machine during washing.

• The water level is not visible from outside of the washing machine. This is not a failure.

Loading door cannot be opened.

• Door lock is activated because of the water level in the machine. >>> Drain the water by running the

Pump or Spin programme.

• Machine is heating up the water or it is at the spinning cycle. >>> Wait until the programme completes.

• Child lock is engaged. Door lock will be deactivated a couple of minutes after the programme has come

to an end. >>> Wait for a couple of minutes for deactivation of the door lock.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Grundig GWN 48430 CW Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Grundig GWN 48430 CW

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info