Bedienungsanleitung GT 970 (Seite 6 von 12) (Englisch)

633024

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

- RAPID TEST (Function No. 4).

With this function it is possible to check the correct system installation carrying out a test of

all the alarm lines.

SEAT/BONNET/SIDESTAND test switch: if the alarm line is triggered the system generates

5 beeps and 5 GREEN flashes of the LED on the receptacle.

SHOCKS/MOVEMENT SENSOR test: to test the position sensor it is necessary to wait 5

seconds from the function enabling before moving the motor vehicle. When the movement

is detected the system generates 2 beeps.

Ignition switched live test: if the alarm line is triggered the system generates 6 beeps and

6 flashes of the GREEN LED on the receptacle.

Wires cut test: removing the power supply to the alarm system a continuous s equence of

beeps will follow. To come ou from the function deactivate the system by the “OFF” button or

wait 30 seconds without triggering the alarm lines. In both ways you come out also from the

set functions.

- ACOUSTIC SIGNAL WHEN ARMING/DISARMING (Function No. 5).

It is possible to program the acoustic signal (beep) to indicate the alarm arming and the

disarming.

1 - Select the function and ENABLE/DISABLE pressing the “OFF” handset button.

- POSITIVE OUTPUT WHEN THE ALARM IS ARMED (Function No. 6).

This output, if enabled, is active 5 seconds after the arming, it can be used to command an

additional module or a satellite system.

1 - Select the function and ENABLE/DISABLE pressing the “OFF” handset button.

- INDICATORS EMERGENCY FLASH (Function No. 7).

This function allows to activate the four emergency flashes (hazard warning) pressing the

“OFF” remote control handset button with ignition key ON. The flash continues even removing

the vehicle ignition key. It is possible to activate and deactivate the system. To switch OFF

the four emergency flashes press the

“OFF” remote control handset button again with the

ignition key ON.

1 - Select the function and ENABLE/DISABLE pressing the “OFF” remote control handset

button.

- AUTOMATIC ANTI-HIJACK (Function No. 8) (Available only with

GT884N).

This function allows to block the motor vehicle in case the user is obliged to leave it with the

engine on ( theft attempt).

1 - Select the function and ENABLE/DISABLE pressing the “OFF” handset button.

- HANDSETS SELF-CODING (Function No.3).

With the function No. 3 it is possible to self-code new handsets to the control unit up to a

max. of 8.

1 - Select the function and press the “ON” button to be self-coded.

2 - The system confirm the correct handset self-coding by a flash of the GREEN LED and

by a beep.

WARNING:

- When you have entered the function the first handset which is self-coded deletes all

the other handsets memorised.

- If you want to add one or additional handsets you have to self-code all of them.

- If you try to self-code an handset already self-coded or the handsets maximum

number has been reached the system emits 3 anomaly beeps.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

GT 970 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info