Bedienungsanleitung Guardall PX (Seite 14 von 52) (Englisch)

580330

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

PX Control Panel User Manual – Issue C

- 14 -

Message Reason

Alarm Abort User logs on within the alarm abort period (programmable option)

Setting Stopped User logs on during the setting exit period

Group Unset A group(s) is set and is programmed to automatically unset when a user logs on.

Cannot Set The system cannot set, the reason(s) will then be displayed.

Unset Alarm An unset alarm has occurred, the details will then be displayed.

Mult.Alarm A circuit(s) has alarmed the maximum number of times allowed (programmable).

The circuit details will then be displayed.

Code Known

Another user has chosen your code. You will then be given the option of

immediately changing your code. This message will always be displayed on log

on until the code is changed.

Call Engineer You should call the installation company. The details will then be displayed.

Reset OK A managed reset code has been accepted

Set

4=Confirm

The user is configured for the log on set option. If confirmed the system will start

setting (if only one group is authorised) or display the set group menu.

Soak Cct Fails Circuits which have been put on special test by the installation engineer have

alarmed.

Dual User Code Operation

Where a higher level of security is required a keypad may have been programmed to require two user

codes to be entered before logging a user on to the system. Both user codes must be authorised and

are logged by the system. The authority of the second user code entered is used by the system.

Unset

Code-01

The system will have been partitioned by the installation engineer into a number of set groups. The user

authority will determine the choice of groups, which can be unset. There are several methods of

unsetting available to the user. These methods are discussed in the following section.

Unsetting Methods

If a set group incorporates an entry route in the unsetting procedure then opening a final entry door to

the area will start a pre-programmed entry timer. The user must proceed directly to the keypad or

keyswitch via a pre-determined entry route and unset the group as described.

If the group is not unset before the entry time has expired a warning period, equivalent to 50% of the

programmed entry time, will be allowed. This is to warn the user that an alarm condition will occur if the

group is not unset by the end of the warning period. If the group is not unset by the time that the total

entry time and warning time has expired, an alarm condition will be initiated.

During the entry time, if a user deviates from the prescribed entry route into an armed area, the entry

time is immediately cancelled. If programmed, a fixed pre-warning period of 45 seconds will be given,

otherwise an immediate alarm will be given. If the user enters an armed area during the entry warning

period, the warning period is cancelled and an immediate alarm will be given.

Unsetting from a keypad

To unset, log on to the keypad. If an authorised group is configured for automatic logon/unset then the

unset group descriptor will be displayed.

Workshop

Unset

If more than 1 group is configured for logon/unset then only the first

descriptor will be displayed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Guardall PX Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Guardall PX

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info