Bedienungsanleitung Guardo Pursuit pro (Seite 8 von 28) (Deutsch, Englisch, Holländisch, Französisch)

751672

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

-8-

INFLATE THE TIRES

The maximum tire pressure is indicated on the tires.

• Remove the front and rear tire inatable mouth cap.

• Connect the pump to inate and tight it to the inatable mouth.

• Replace the mouth cap when nish pumping.

SPECIFICATIONS

• Max. continuous rated power: 350 W

• Max. tire pressure: 2.5 bar

• Max load: 120 kg

• Min. height of user: 130 cm

• Suitable age: 14+

• The A-weighted emission sound pressure level at workstations, is less than 70dB(A)

• The peak C-weighted instantaneous sound pressure value at workstations, is less than 63Pa

• The A-weighted sound power level emitted by the machinery, is less than 80dB(A)

CARE & MAINTENANCE

WARNING! As with any mechanical component, a vehicle is subject to high stresses and wear. The

various materials and components may react differently to wear or fatigue. If the expected service

life for a component has been exceeded, it may break suddenly, therefore risking causing injuries to

the user. Cracks, scratches and discoloration in the areas subject to the high stresses indicate that the

component has exceeded its service life and should be replaced.

Your E-Scooter Pursuit Pro will require regular maintenance. Please use following checklist to ensure

your E-Scooter runs smoothly for a longer time.

• Charge your battery often. Avoid charging your battery for too long to avoid damage to it.

• Always allow your battery to cool before charging to help increase your battery’s life expectancy.

• Avoid riding in wet conditions when possible, to avoid excessive exposure and corrosion.

• Keep all moving components clean. Once a week, use a clean, damp cloth to wipe off dust and

grime that collected on the handlebars and stem. Wash the deck with lukewarm water and a bit

of dish soap. Take care not to get the electrical components wet. Let the components dry before

you use the scooter again.

• Check your brakes, brake discs, and rotors for wear and tear on a weekly basis. Do not ride your

E-Scooter if the brakes don’t respond properly.

• Check your E-Scooter’s tire pressure on a regular basis. Proper ination helps you reach

maximum speed without taxing your motor.

• Inspect all cables for wear and tear regularly. If you notice any damage to the cables or their

housing, they may need to be replaced.

• The self-tightening nuts, as well as the other self-tightening fastenings, may lose their efciency.

They may need to be retightened as follows: M4 bolt: 2.5~3.5 N/m - M5 bolt: 4~6 N/m - M6 bolt:

12~14 N/m - M7 bolt: 27~29 N/m.

• If you’re using your E-Scooter as your primary means of transportation, it is advised to contact

your reseller and schedule an annual inspection with a qualied maintenance shop.

• Keep all joints and parts, such as brakes and hinges, lubricated. Please lubricate at least once

a month to keep the scooter in good condition. Please use lubricants designed for bicycles and

scooters.

• Store your E-Scooter in a safe place (inside) to prevent damage to electrical parts or the battery.

Choose a location that’s out of direct sunlight and in an area where temperatures are steady.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Guardo Pursuit pro Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info