Bedienungsanleitung Gude 200-400 w 69010 (Seite 10 von 38) (Deutsch, Englisch, Dänisch)

628835

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

not take the device to refuse storal area. Herewith you will

contribute to protection of environment.

The instructions for disposal are described on pictograms

placed on the device, and/or on its packing. For the

description of individual meanings see Chapter “Marks on the

Device”.

Requirements on the Operator

The Operator should carefully read this Operation Manual

before using the device.

Qualification

The professionally adept person needs just detailed training

of how to operate the device, no special qualification is

required.

Minimum Age

The device may be operated only by persons older than 16.

The exception is when using the device by an adolescent

during his/her preparation for profession, where the device is

used for the purpose of getting skill under supervision of the

trainer.

Training

The device can be operated by a person trained by a

professionally adept worker or be trained according to the

Operation Manual. No special training is necessary.

Technical Data:

Assortment Position No. 69010

Permanent output [W] 200

Max. output [W] 400

Inlet voltage [VDC] 10-15

Outlet voltage [VAC] 220-240

Frequention [Hz] 50

Wave shape

Modifed sinusoid wave

Efficiency 90%

Permanent current force

[mA]

250

Protection against low

voltage [V]

10±0,5

Caution – low voltage [V] 10,5±0,5

Protection against

overvoltage [W]

200

Cabel length [cm] 76

Fan Yes

Protection

Protection against

overloading, protection

against overheating,

protection agains shortcut,

protection against reverse

of poles

Operation

Battery Alarm Signal

• As soon as supply voltage of the battery drops under

10,5 V, the alarm signal sounds.

• Disconnect all appliances from the Voltage Changer.

• Disonnect the Voltage Changer from the battery.

• Battery shall be immediately charged so that the

damage on battery may be prevented.

• The Voltage Changer will disconnect all appliances from

the battery beginning with the value of 10 V, for

prevention of excessive discharge of the battery.

• Should the alarm signal sound although the voltage is

sufficient, there si another problem. In this case refer to

Chapter “Repair of Defects”“

• Instruction: A short alarm signal may sound during the

connecting the Voltage Changer with terminals and its

disconnecting. It is a common feature and it does not

indicate a problem on the device or any failure..

Service Life

• Usually one charging of the battery that is in good

condition is sufficient for 1 to 2 hours of operation. The

duration depends particularly on the connected

appliances.

• In order to prevent too high decrease of the battery

voltage, start the vehicle engine after an hour and

disconnect all appliances (light, ventilation, radio etc.)

Protective Mechanisms

The Voltage Changer supervises continuously a few

parameters of power supply and current consumption.

Autorestart Function

The device automatically switches the device on after it has

been repaired (switching of the protection). The fuse need not

be replaced.

Low Voltage

Should the Changer alarm signal sound reporting the low

voltage (from 10,5 V), it is not dangerous for the Changer.

The alarm signal serves for signalization of decrease of

supplying battery voltage. As soon as the voltage drops under

10 V, the device will disconnect the appliances.

Shortcut

By shortcut supervision can be checked if the connecting

cables have not reversal polarity or if there is a shortcut in the

system. Should this protection respond, disconnect the

appliances from the Changer and check all supply lines of the

Changer.

Overheating

As soon as tempereture of internal cooling bodies exceeds

65 °C, the protection relais of the Changer will disconnect

appliances, so that the device may be cooled. After the

Changer has been cooled, it is automatically reswitched. No

intervention of user is needed. Check if the appliances do not

consume too much current, disconnect them if necessary.

Overloading

The Voltage Changer will automatically switch off if the

appliances consume more permanent and/or closing current

than the values the device is designed for (see the Cahpter

“Technical data”). Disconnect large appliances. The device

will automatically switch on as soon as the loading fluctuates

within normal range.

Failures-Causes-Repairs

CAUTION: FIRST CHECK PROTECTION MECHANISMS !

Before all works on the device pull out the plug from the

network..

• The plastic parts are cleaned with a wet cloth. Do not

use any detergents, solvents or pointed things.

Safety Instructions for Inspection and Maintenance

Only the device on which regular maintenance is performed

and which is well cared for will be helpful. Failures in the

maintenance and care may cause unpredictable accidents

and injuries..

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude 200-400 w 69010 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info