Bedienungsanleitung Gude 400-10-50 N 50015 (Seite 14 von 68) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

621180

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Operating Staff Requirements

The operating staff must thoroughly read the operating

instructions before using the machine.

Qualification

No additional qualification is needed for using the device

apart from detailed training by a person with expert

knowledge.

Minimum Age

The device may only be operated by persons that have

reached 16 years of age.

An exception includes device use by juveniles within job

preparation for purpose of reaching skills under

instructor's supervision.

Training

Appropriate training is only needed for device use. No

special training is necessary.

Transportation and Storage

 If the device is stored for a longer period of time it

needs to be thoroughly cleaned and stored so that it

was not accessible to unauthorised persons.

 The compressor must never be stored or transported

laying or under pressure!

 Pressure in the air jet may be reduced at

compressed air cooling.

Assembly / First Putting into Operation

If the compressor is supplied without wheels assemble it

with a screw wrench according to pic. 2. The sequence of

screws, nuts and washers is evident from pic. 2. In case

of need, a rubber foot also needs to be screwed on.

Jointing materials, such as screws, nuts, etc. are included

in the supply.

Transport stopper of the oil tank needs to be

exchanged for throat for oil adding and correct oil

level needs to be ensured (see the "Handling Throat

for Oil Adding and Oil Level Inspection" chapter)

before putting the compressor into operation)

Check the oil level at every startup!!!

Handling

Pull the connector plug out of socket before

each maintenance, arrangement and adjustment of

the compressor.

Working Pressure Adjustment

 The working pressure may be adjusted very easily:

By turning the knob (2) in the + direction the

working pressure increases. By turning the knob

in the – direction the working pressure reduces.

The working pressure may be locked by

tightening the snap ring.

 The compressor is equipped with an automatic

safety valve releasing pressure at overpressure.

You may release pressure from the air jet

manually by pulling the valve ring (10).

ATTENTION:

Realise the amount of compressed air you will need from the

device! The pressure itself, however, is NOT decisive for perfect

and sufficient operation. Short switching the compressor on after

a long break without use is common!

Have any repairs executed exclusively at qualified specialists.

Turn the compressor never about the power,

otherwise no discharge of the unit is done. Without

discharge, the electric motor through the back pressure

damage!

Throat for Oil Adding and Oil Level Inspection

Transport stopper needs to be exchanged for throat

for oil adding and correct oil level needs to be ensured

before putting the compressor into operation.

Check the oil level at every startup!!!

Oil change

Since arriving on the piston can chip, it is absolutely

necessary after the first 10 hours of operation to carry out an

oil change. We recommend that you are our compressor

(SKU: 40056). Later, depending on the operation of the

compressor, all 100 to 200 hours of operation an oil change

place. In order to carry out oil changes, open the drain screw

(16) and begin the process of waste oil in a suitable

container.

Observe strictly the rules for disposal of waste oil and

dispose of it properly in a waste oil collection center.

Unscrew the drain screw is now firmly back on and fill oil up

to the mark on the dipstick

In winter we recommend a lubricity oils to start during

the cold season to help!

Air-pressure switch:

The compressor is equipped with an automatic air-pressure

switch that will switch the compressor off after reaching the upper

limit of the operating pressure and switch it on again when air is

needed. Starting pressure of 8 bar, max. pressure of 10 bar.

Inspections and Maintenance

Pull the connector plug out of socket before each work on the

machine. If you are not going to use the device for a longer period

of time we recommend dropping a few oil drops at the place of air

filter insertion so that walls of cylinders were lubricated at next

compressor switching on.

 Use a damp cloth for cleaning of plastic parts. Do not use

cleaners, solvents or sharp objects.

 Clean the air holes and mobile parts with a soft brush off the

settled dust after each use.

 Regularly paint all metal parts with oil.

After each use

clean the air holes and mobile parts off dust.

Regularly

paint metal parts with oil (universal oil)

check whether all screws are tightened.

Regularly (once a month at least) release the condensed fluid

from the air jet; failing to observe this regulation may lead to

guarantee for rusting through expiry – apart from that, the

compressor is maintenance-free.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude 400-10-50 N 50015 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info