Bedienungsanleitung Gude 40645 ISG 1000 (Seite 16 von 60) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

628845

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

The given maximum input value must not be

exceeded in any connecting plug.

AC operation:

• Start the engine and make sure the indicator (pic. 1/5 or

2/5) is green.

• Make sure that the used appliance is switched off. If so,

plug the appliance to a three-phase outlet (pic. 1/3 or

2/3).

Do not exceed the maximum rated power of the

generator!

If overload signalling (pic. 1/6 or 2/6) lights up shortly

or constantly, the appliance may get damaged. In such

a case, the generator switches off while the combustion

engine keeps running with no change - replace

immediately the consumer with a consumer with safe

performance and start the generator again.

DC operation:

The DC outlet may only be used to charge a 12 V

battery.

Under DC operation, the Eco throttle valve switch (pic. 12)

must be in the OFF position.

• Connect the feeder cable with the DC outlet and battery

terminals (pic. 13). To prevent sparking, the feeder

cable must be first connected to the generator and then

the battery. To disconnect the feeder cable, release the

battery cables first.

If the generator is

connected to a battery, do not start the vehicle

engine.

• Start the engine.

If the DC circuit is overloaded, the safety switch (pic.

1/10 or 2/10) jumps out. In such a case, wait for a few

minutes and then press the button inside and continue

in your work.

Switching off:

• Switch the connected appliance off and unplug it.

• Put the ignition switch (pic. 1/11 or 2/11) to the OFF

position.

• Put the fuel tank cap ventilation lever to the OFF

position (pic. 1/1 or 2/1).

Lack of oil signalling:

Before the oil level drops too low, the engine switches

automatically off. The indicator (pic. 1/8 or 2/8) is red and

the engine is not running when the starter is put into action.

In such a case, check the oil level and add some.

Safety instructions for the operator

To put the appliance into operation for the first time, see the

General safety instructions, Appliance-specific safety

instructions and Safety instructions for first starting up.

• Use the appliance only after careful reading of the

Operating Instructions.

• Follow all safety instructions included in the Operating

Instructions.

• Behave responsibly to other persons.

Inspections and servicing, pic. 1+2+3+4+5+6+7+9+11

Regular cleaning and servicing are necessary to provide

perfect working and long service life of the appliance.

Appliance adjustment to be only performed when

the appliance is unplugged. Significant risk of injury.

Do not smoke when performing the below-mentioned

works.

Never work near sparks, flames or open fire.

Regular servicing and inspections

Air filter

The air filter should be cleaned every 50 hours of operation.

• Release the bolt (pic. 3/1) and remove the cover (pic. 3/2).

• Release the air filter cover bolt (pic. 5/1).

• Remove the air filter cover (pic. 5/2).

• Check the external and main filter (pic. 5/3+4) and wash it

in non-flammable or little flammable solvent and let it dry

out if necessary.

• Drop small amount of oil on the air filter and press it.

• Refit the filter.

• Fasten the air filter cover bolt (pic. 5/1).

• Tighten the cover (pic. 3/2) and the cover bolt (pic. 3/1).

The appliance must never be used without the air

filter as it could quickly wear the engine out.

Spark plug

• Remove the servicing cover off the spark plug (pic. 6/1).

• Remove the socket plug (pic. 6/2).

• Remove any dirt and dust off the bottom of the spark plug.

• Using the spark plug spanner (pic. 7/1), screw the spark

plug out.

• Check the spark plug for any cracks and scratches. If the

spark plug has any sign of damage, dispose it

immediately.

• If the spark plug can still be used, clean it by a wire brush.

• Now check the distance of electrodes by a feeler gauge.

Bend the side electrode and provide the proper distance

(proper distance: 0.6 to 0.7 mm).

• Refit the spark plug.

• Refit the socket plug (pic. 6/2) on the spark plug.

• Refit the servicing cover (pic. 6/1).

Oil change

Engine oil to be discharged when the engine is warmed up to

make sure it is emptied quickly and to the full extent.

Before discharging, make sure the fuel tank cap

ventilation lever (pic. 1/1 or 2/1) is in the OFF position.

• Release the cover bolt (pic. 3/1).

• Remove the left cover (pic. 3/2).

• Remove the oil tank cap (pic. 4/2).

• Discharge the engine oil to an appropriate container (pic.

• Add the recommended engine oil (SAE 10W-30, pic. 10)

and check the engine oil level (pic. 4/3).

• Fit the oil tank cap (pic. 4/2).

• Refit the cover (pic. 3/2) and tighten the bolt (pic. 3/1).

After coming into contact with the waste oil, hands should be

thoroughly washed with water and soap.

Please observe the applicable environment protection

provisions when disposing the waste oil. We recommend

taking the waste oil to a waste oil collection centre in a

closed vessel. Do not put the engine oil to waste and do

not pour it on the ground.

Noise suppressor check

Let the noise suppressor cool down before any

servicing.

The spark catcher must be checked every 100 hours

of operation to make sure it works perfectly.

• Remove the four bolts and the cover.

• Now remove the three 6-mm bolts (pic. 9/1), then the noise

suppressor (pic. 9/2), spark catcher (pic. 9/3) and sealing

(pic. 9/4).

Gude 40645 ISG 1000 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info