Bedienungsanleitung Gude 85056 (Seite 13 von 19) (Deutsch, Englisch)

628861

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

 Screw the closing nut on the connecting tread (left

thread) – put the protective cover on.

 Connect the new cylinder and check tightness.

Start up procedure / discontinuation or stopping procedure of

the catalytic stove:

 Before operation, let the cylinder stand in a vertical

position for 1 hour if transported so the elements

more burdening to the environment may settle down

to the bottom of the cylinder.

 Place the gas cylinder to the inner space of the

device (back side). Connect the gas cylinder as

described above.

 Open the cylinder valve on the propane cylinder by

turning to the left.

 Push the large setup button down and turn it to the

large flame symbol – start.

 Push the piezo-ignition button several times, to light

the starting flame. When the starting flame is visible,

keep the setup button pushed for about 20 seconds,

heating up the thermal element. You can release the

setup button afterwards and the heating is turned on

to the highest level. If the starting flame goes off,

though, repeat the procedure.

 The heating output can be lowered by pushing lightly

on the setup button and turning it to the medium or

minimum flame symbol. We recommend to wait for 10

minutes after starting the operation before changing

the heating output.

 The catalytic gas plate is slightly hot only in the area

of the starting flame, but the full heating output is

spread over the whole catalytic plate.

 The slight smoke (fresh paint) will dissipate after

heating up.

CAREFUL! Do not move when hot (transport).

 The gas cylinder must not be turned during the

operation or shut down of heating device. The highest

danger of accident!

 Shutting off of the catalytic gas heating device:

CLOSE THE GAS VALVE ON THE CYLINDER.

Illustration 3:

The devices are supplied with an electric heating ventilator

allowing for an increase of 2 x 1000 W as an addition to

the regular gas burning by the device.

 Electric power supply cable (rolled up inside the

device) (1) should be connected to a socket of 230V-

50Hz.

 Push the heating ventilator switch. There are 4

positions of the switch: (2)

= ventilator off

= ventilator only

= ventilator + 1000 W

= ventilator + 2000 W

Inspection and maintenance

 Any dirt on the case of the device can be cleaned off

with a wet towel. Water must not get onto the surface

of the catalytic burner.

 Do not use any abrasive cleaning means or solvents

for cleaning.

 In case of a longer discontinuation of use, disconnect

the gas cylinder and place it outside of the device,

store the device in a dust-free environment.

 Contact your contractual sales point for more

extensive maintenance.

 Use only original spare parts for repairs.

 Such maintenance should be performed at least once

every 2 to 3 years.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude 85056 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info