Bedienungsanleitung Gude Blueflame 4200 B 85079 (Seite 12 von 71) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

628847

Zoom out

Zoom in

Vorherige Seite

1/71

Nächste Seite

Safety prevention means:

• Touch protection at the device should prevent fire and

burns; no part of the protection can be taken off

permanently.

Full protection is not provided for children and ill

persons!

• The heating device is equipped with a low-oxygen

safety device. If a higher concentration of carbon

dioxide (CO2) is detected in the room, the safety

device will automatically shut the appliance off. The

appliance cannot be turned back on until the room is

ventilated properly.

• After use of the heating device, the cylinder valve

must be turned off!

Operation

After having read the general safety instructions and

the device-specific safety instructions and having

understood them, you can start operating the device.

Follow these instructions:

Installation of the gas cylinder:

• The device uses a mixture of propane and butane

under pressure of 50 mbar.

• To operate the device, a gas cylinder with liquid gas

of max. 11 kg of filling is necessary, the hose is pre-

installed.

• Gas regulator must be selected and/or purchased first

of all, depending on the purpose of use.

• Installation or change of cylinder with liquid gas must

be performed in non-flammable atmosphere.

• When the device is not in use and during change

of the cylinder, the device valve must be turned

off.

• After the first and before any subsequent putting into

operation and especially after each bottle change, a

leak test using foamy solution (e.g. soapy water) must

be carried out.

• Tightness is proven when no bubbles appear.

It is strictly forbidden to check tightness by open

flame!

• The cylinder must be placed in such a position so that

it is not in contact with the sheet metal of the burner

and the gas supply attached to it. The hose must not

touch (be in contact with) the hot back side of the

burner.

• The device is supplied with a 40 cm long hose. The

hose must not be shortened or exchanged for a

longer one.

• Inspect the condition of the hose regularly, at least

during each change of the cylinder.

• In case of damage to the hose, it must be replaced

with a hose of the same construction, tested

according to DIN DVGVV.

• Connection of the hose to the regulator must be done

with minimum of V4" left thread. The screw spanner

SW 17 is required for installation.

• Twisting or distortion of the gas hose during the

installation of the hose and pressure regulator to the

liquid gas cylinder is not permissible.

Warning! The hose must not touch (be in contact

with) the hot back side of the burner!

• Operation with pressure regulators other than those

prescribed above is prohibited.

• Make sure the hose and regulator are changed after

5 years at the latest.

Connection of the liquid gas cylinder:

• Take the protective cover of the valve off.

• Take the covering nut from the attachment socket off

by turning (right).

• Check the rubber seal in the cylinder valve (regulator

connection).

• The regulator and the hose must be screwed on

tightly (left thread). No not use any tool or instrument.

Do not turn the regulator but the sleeve nut.

• Check the tightness of the connection.

Change of the liquid gas cylinder:

• Close the cylinder valve

• Unscrew the regulator.

• Screw the closing nut on the connecting tread (left

thread) – put the protective cover on.

• Connect the new cylinder and check tightness.

Start up procedure / discontinuation or stopping procedure of

the catalytic stove:

• Before operation, let the cylinder stand in a vertical

position for 1 hour if transported so the elements

more burdening to the environment may settle down

to the bottom of the cylinder.

• Place the gas cylinder to the inner space of the

device (back side). Connect the gas cylinder as

described above.

• Open the cylinder valve on the propane cylinder by

turning to the left.

• Push the large setup button down and turn it to the

large flame symbol – start.

• Push the piezo-ignition button several times, to light

the starting flame. When the starting flame is visible,

keep the setup button pushed for about 20 seconds,

heating up the thermal element. You can release the

setup button afterwards and the heating is turned on

to the highest level. If the starting flame goes off,

though, repeat the procedure.

• The heating output can be lowered by pushing lightly

on the setup button and turning it to the medium or

minimum flame symbol. We recommend to wait for 10

minutes after starting the operation before changing

the heating output.

• The catalytic gas plate is slightly hot only in the area

of the starting flame, but the full heating output is

spread over the whole catalytic plate.

• The slight smoke (fresh paint) will dissipate after

heating up.

CAREFUL! Do not move when hot (transport).

• The gas cylinder must not be turned during the

operation or shut down of heating device. The highest

danger of accident!

• Shutting off of the catalytic gas heating device:

CLOSE THE GAS VALVE ON THE CYLINDER.

Servicing

Do you have any technical questions? A claim? Do you

need spare parts or the Operating Instructions?

You will be helped quickly and without needless

bureaucracy at our webpage www.guede.com in the

Service part. Please help us be able to assist you. To be

able to identify your appliance when claimed, we need to

know its serial No., order No. and year of production. All

these details can be found on the type label. Enter the

details below for future reference.

Serial No.:

Order No.:

Year of production:

Tel.: +49 (0) 79 04 / 700-360

Fax: +49 (0) 79 04 / 700-51999

E-Mail: support@ts.guede.com

wenn ich nach dem starten den aufgedrehten gasregler auf normale flamme einstellen möchte, geht der ofen immer aus. woran kann das liegen? Eingereicht am 24-11-2019 09:25
Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.

Neu registrieren

Registrieren auf E - Mails für Gude Blueflame 4200 B 85079 wenn:

neue Frage gestellt werden
neue Handbücher vorhanden sind

Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.

Gude Blueflame 4200 B 85079 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.