Bedienungsanleitung Gude Blueflame 4200 T 85121 (Seite 10 von 56) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

628856

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

It is strictly forbidden to check tightness by open

flame!

 The cylinder must be placed in such a position so that

it is not in contact with the sheet metal of the burner

and the gas supply attached to it. The hose must not

touch (be in contact with) the hot back side of the

burner.

 The device is supplied with a 40 cm long hose. The

hose must not be shortened or exchanged for a

longer one.

 Inspect the condition of the hose regularly, at least

during each change of the cylinder.

 In case of damage to the hose, it must be replaced

with a hose of the same construction, tested

according to DIN DVGVV.

 Connection of the hose to the regulator must be done

with minimum of V4" left thread. The screw spanner

SW 17 is required for installation.

 Twisting or distortion of the gas hose during the

installation of the hose and pressure regulator to the

liquid gas cylinder is not permissible.

Warning! The hose must not touch (be in contact

with) the hot back side of the burner!

 Operation with pressure regulators other than those

prescribed above is prohibited.

 Make sure the hose and regulator are changed after

5 years at the latest.

Connection of the liquid gas cylinder:

 Take the protective cover of the valve off.

 Take the covering nut from the attachment socket off

by turning (right).

 Check the rubber seal in the cylinder valve (regulator

connection).

 The regulator and the hose must be screwed on

tightly (left thread). No not use any tool or instrument.

Do not turn the regulator but the sleeve nut.

 Check the tightness of the connection.

Change of the liquid gas cylinder:

 Close the cylinder valve

 Unscrew the regulator.

 Screw the closing nut on the connecting tread (left

thread) – put the protective cover on.

 Connect the new cylinder and check tightness.

Start up procedure / discontinuation or stopping procedure of

the catalytic stove:

 Before operation, let the cylinder stand in a vertical

position for 1 hour if transported so the elements

more burdening to the environment may settle down

to the bottom of the cylinder.

 Place the gas cylinder to the inner space of the

device (back side). Connect the gas cylinder as

described above.

 Open the cylinder valve on the propane cylinder by

turning to the left.

1.) Turn the control knob to position 1/. Ignition; Pic. (3-C)

2.) Press and hold the START button; Pic. (3-B)

3.) Press the piezoelectric ignition button several times until

eternal flame is produced. Pic. (3-A)

4.) Hold the Start button pressed for about 20 seconds until

the flame is stable.

5.) If external flame of the burner fails to be ignited at the

first attempt, wait for about 30 seconds and repeat steps 2-

4. Setting the thermostat; Pic. (3-D)

Set the thermostat to an average temperature for switch-

off.

Set the gas heater to a full heating output (level 5) and let it

heat until the thermostat switches off.

(the flame will automatically diminish). Measure the

temperature in the room.

When the temperature in the room is too low, turn the

thermostat regulator (pic. 3-D) slightly more to the left. (the

flame will automatically increase)

If the temperature in the room is too high, turn the

thermostat regulator (pic. (3-D) to the right and let the

room cool down. (the flame will automatically diminish).

Do these actions for as long until the required switch-off

temperature is reached.

Now the temperature in the room will automatically be

controlled by the thermostat, which will automatically

increase or diminish the flame.

CAREFUL! Do not move when hot (transport).

 The gas cylinder must not be turned during the

operation or shut down of heating device. The highest

danger of accident!

 Shutting off of the catalytic gas heating device:

CLOSE THE GAS VALVE ON THE CYLINDER.

Service

Any technical questions? Complaint? Do you need

spare parts or operation manual?

Go to our website www.guede.com and the section

Service will help you quickly and without bureaucracy.

Please, help us to help you. In order to identify your device

in case of complaint, please indicate serial number, order

number and year of manufacture. All information is

available on the product label. To have all information

always at hand, put them down.

Serial number:

Order number:

Year of manufacture:

Phone: +49 (0) 79 04 / 700-360

Fax: +49 (0) 79 04 / 700-51999

E-Mail: support@ts.guede.com

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude Blueflame 4200 T 85121 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info