Bedienungsanleitung Gude DHH 1050-11 T ECO 02012 (Seite 26 von 173) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

624553

Zoom out

Zoom in

Vorherige Seite

1/173

Nächste Seite

Open the fuel tap

Put the engine switch to the “ON“ position (pic. 3)

Make sure the engine is cold when being started.

Turn on the engine choke (pic. 4; pos. “CHOKE“)

Turn the speed control lever (pic. 4; pos. “START“) to full speed.

First, pull shortly the starting cable so that it is stretched. Now pull the starting cable slowly to the stretched

position with your left hand resting on the engine and one more strong pulling the starting cable. Turn the

engine choke off as soon as the engine gets started (pic. 4; pos. “RUN“)

Give full throttle using the speed control lever (pic. 4; pos.”HARE”)

To be provided

The starting cable must not reel automatically. It must always be reeled back by hand. If the engine fails to

start even after several attempts, check whether the tank has been refuelled properly. Maybe there is too

much fuel in the roll, which has caused the spark plug to get damp.

Switching off the engine

Put the speed control level to the idle gas position (pic. 4; pos. Želva).

Use the engine switch (pic. 3; pos. “OFF”) to switch off the engine. Never leave the appliance unattended

when the engine is running. Never switch the engine off when the choke is on as the engine could get

damaged. Close the fuel tap (pic. 2; pos. “OFF“). Pull slowly the starter handle until you feel resistance. By

this, valves get closed.

This step is necessary to prevent moist air from entering the combustion chamber from outside.

1. Put the wood to be split on the table as short or long logs and set the backward movement

accordingly (see Lift setting).

2. Now clasp the split wood with both operating arms (see Stop screw setting) and press them down

at the same time.

3. Remove the split wood from the working area and put another wood on the table.

4. If the splitting knife is greased from time to time, more difficult wood can also be split.

Start the splitter and wait until the splitting column gets to the starting position.

Now press both operating levers to make the splitting column go down. Press just the right or left operating

lever in turn. If the splitting column stands each time, you can use the splitter with no worry.

If the splitting column keeps going down, the two-hand operation must be subject to new

calibration.

For that purpose, contact an authorised workshop.

V nebezpečných situacích a při nehodách musíte dát páku pro regulaci otáček co možná nejrychleji

do polohy „STOP“ a motor vypnout spínačem motoru (obr. 3; poz. „OFF“).

Hydraulic

Hydraulic hoses and joints need to be checked for tightness after app. 4 hours of operation and

tightened if necessary.

Hydraulic oil/tank

Regularly sold hydraulic oil (e.g. HLP 46) or any other product of identical viscosity can be used for all

splitters.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude DHH 1050-11 T ECO 02012 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info