Bedienungsanleitung Gude druklucht set-40065 (Seite 9 von 34) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

622215

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

Servicing and maintenance

Servicing may only be provided by trained persons.

Long operating life and failure-free operation of this high-quality product will be provided by following the servicing instructions

specified in this manual. Disconnect the appliance from the compressed air source for servicing and maintenance purposes. To

ensure permanent failure-free operation of the appliance, everyday cleaning and regular lubrication need necessarily be provided.

For that, special pneumatic oil must be used only. Our special pneumatic oil for oil-fog lubricators #40060 is recommended.

The following options are available for lubrication purposes:

a) using an oil-fog lubricator

The full maintenance unit includes an oil-fog lubricator (e.g. Güde ¼“ SB #41080 lubricator) and is placed on the compressor.

b) using a pipeline grease box

A grease box (e.g. Güde #41086) sufficiently supplying the appliance with oil is installed on the pipeline in the immediate vi-

cinity of the appliance (distance of app. 50 cm).

c) manually

If no maintenance unit or pipeline grease box is available for your appliance, 3 - 5 oil drops must be added to the compressed

air connection every time you are going to put the pneumatic appliance into operation. If the pneumatic appliance has been

out of operation for a couple of days, 5 – 10 oil drops must be added to the compressed air connection before starting the ap-

pliance. Keep the pneumatic tools and appliance in dry spaces.

Caution:

Replace the spring (pos. 1) from time to time

Failure – cause - removal

Failure Cause Removal

Air control is set to a too low value. Set the air control to a higher value.

Knife is worn out. Replace the knife.

Operating (hydraulic) pressure is too

low.

Increase the operating (hydraulic) pres-

sure while respecting the maximum op-

erating pressure value.

Too low output of the compressor. Use a compressor of different output.

Too small diameter of the hose. Use a hose of appropriate diameter.

Cutter not working properly

Bypass valve is worn out. Contact the manufacturer or an author-

ised service partner.

Service

Any technical questions? Complaint? Do you need spare parts or operation manual?

Go to our website www.guede.com and the section Service will help you quickly and without bureaucracy. Please, help us to

help you. In order to identify your device in case of complaint, please indicate serial number, order number and year of manufac-

ture. All information is available on the product label. To have all information always at hand, put them down.

Serial number:

Order number:

Year of manufacture:

Phone: +49 (0) 79 04 / 700-360

Fax: +49 (0) 79 04 / 700-51999

E-Mail: support@ts.guede.com

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude druklucht set-40065 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info