Bedienungsanleitung Gude ECO WHEELER 1500 E95120 (Seite 31 von 43) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

626231

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

Best work presumptions:

1. Grass should be dry completely!

Advantages:

a. Cutting tool chamber will not get

obstructed with wet grass and the

grass is blown back in the collecting

bag

2. Grass should not be longer than 15cm!

Advantages

a. The passage to collecting bag will

not get jammed.

b. The collecting bag will be filled up

and it won’t be necessary to empty it

so often.

3. The cutting tool should be sharp at any time!

Advantages

a. The grass is not thrown but cut and

will retain nice colour.

The manufacturer shall not be held liable for any

damages if the generally valid regulations and

provisions contained herein are not observed.

Safety Instructions for First Putting in

Operation

Always take care of the screwed joints to see that they

are tightened and use only the parts included in the

delivery.

Make sure that the cutting height is set up at the

highest distance from the ground before the first

switching on to prevent any damage to the unit.

Procedure

Follow the order of assembly of the parts. Observe the

arrangement of parts to respective figures.

Operation

Cable pull relief Fig. 6

To avoid accidental unplugging the cable form the

switch/plug assembly, make sure the cable is correctly

fitted to the cable pull relief device.

Any electrical connections, such as extension

cable should be of approved waterproof design for

outdoor use.

Cutting height adjustment Fig. 7

The cutting height is adjusted by moving the lever

within a raster. Six various settings are possible:

• Lever on the left means lower cutting height

• Lever on the right means larger cutting height

When the motor is on, the unit should not be tilted,

only on the operator-reverse side, if necessary for

switching on.

Unit switch on/off Fig. 8

Push the button (1) and move the switching lever if

necessary with the button pressed. (2). The it is

possible to release the button.

After the switching lever is released, the button

will come back in it original position and switch

the unit off.

When the motor is on, the unit should not be

tilted, only on the operator-reverse side, if

necessary for switching on.

Operation Safety Precautions

• Do not use the unit before you have read the

instruction manual.

• Observe all the safety instruction contained

herein.

• Be responsible to other persons.

• Look out for the connection cable very carefully for

it not get caught or cut.

• The machine is equipped with the cutting tools

brake that makes them stop within 3 seconds after

enabling the switch. Never, under no

circumstances attempt at stopping the cutting

tools or tilting the machine with the tools still

rotating. Wait until they come to a stop by

themselves.

• If the cutting tools get in contact with a foreign

matter, the operating switch has to be put off

(disconnected from the mains) immediately. When

the cutting tools come to a stop, check the

machine for damage. Go on with the work

provided that the machine is unimpaired.

• Walk, while working, do not run.

• Always walk forward while working. Never pull the

machine backward. .

• On a slope, always aerate crosswise, never

upward and downward. A special attention should

taken to changing direction.

• The cutting tools should not be in operation when

crossing areas not overgrown with grass and

when approaching and leaving the work site.

Always use the machine connected to the mains

via protection automatic switch (FI)!

Step by Step Instructions

1. Put the mower on the lawn where grass as short

as possible for the mower to start up easily.

Within the area to be cut, there should be no

stones and clods. They could be thrown off and

cause severe injuries.

2. Fit in the grass collecting bag according to chapter

Assembly and Initial Operation

3. Set the cutting height (chapter Operation)

according the grass length

4. Hang the cable in the pull relief device (chapter

Operation).

5. Plug the unit and switch it on according to

description.

6. Move the unit slowly and evenly on the grass. If

the motor gets too loaded, adjust the cutting

height and mow by stages.

7. If there is much grass left on the ground, empty

the collecting bag.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude ECO WHEELER 1500 E95120 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info