Bedienungsanleitung Gude GBF 550 - 48140 (Seite 15 von 64) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

623151

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Transport and storage

• You should clean the machine properly when storing

for long period of time. Store the machine in clean and

dry place with restricted access of unauthorized

persons.

• Fix the machine properly before every transport so it

will not turn over.

Installation / First start up

Pull the plug out of the socket before every

installation and adjustment. To avoid damage during the

transport, transport the machine in vertical position, in

original package if possible. Keep in mind the weight of the

machine and use corresponding transport vehicle with

sufficient loading capacity. If you do not have a vehicle to

your disposal, handle the machine carefully so you don’t

cause harm to people neither to machine. Protect the

machine from wet, humidity and rain. It is allowed to install

the machine in dry and ventilated rooms only. A working

temperature range for the machine is the best between

+15°C to +40°C. Are the chuck tools and mill fixed

properly? Check for loose machine parts. Is the revolution

range set properly? Are the machine and the fastening

device clean and chips free? Check if the fixing screws of

the 3-jaw chuck are fastened and if you are able to turn the

spindle with your hand easily. Before the commissioning

make sure that all guards and safety devices are in place.

The jaw chuck must rotate. Before you press the start

button check again if everything is installed correctly and

movable parts are moving. Check if the type label figures

match with power supply figures before installation. Install

the lever handles which are part of the delivery.

Installation

Position the machine on flat basement (working bench, etc.)

The machine must be fixed tightly to a base by four

screws. Use four fixing holes drilled into the machine base

frame. Make sure there is enough room for cross-table

movement and there is angle adjustment available. Make

sure that the base for the machine is stabile enough and is

able to bear its weight. All parts have been greased in the

workshop against the corrosion. Clean the machine with

convenient ecological detergent before commissioning. Do

not use detergents that could damage the paint and ensure

proper ventilation during the cleaning. Lubricate the

machine again after the cleaning with light lubrication acid

free oil.

Oil, grease and cleaning detergents can cause harm

to environment so must be disposed ecologically. Do not

dispose it into the domestic waste.

Connecting to power supply/switch

Machine can be used only with monophase current

230V~50 Hz. Electric circuit must have maximum protection

of 16A in domestic use.

Turning on (pict. 3)

Before turning the machine on there must be a folding

guard against the metal chips down (16).

If the green light is on (a) you can start the machine by

revolution selection switch (6) and set the desirable

revolutions.

If the orange light is also on (b) the revolution selection

switch must be put to “zero” position first. Then you can set

the revolutions on the machine and it will start.

Turning off

You can turn off the machine by pressing the red button “0” or

by pressing the emergency switch (c). Then the machine must

be disconnected from the power supply.

Operation and setting

Adjust the machine with the cord plugged out only.

Risk of injury.

Revolutions setting (pict. 3, 4)

You can choose between two revolution ranges by using the

shift bar (5).

Front position (1) for revolution range between 0 - 1100 min

-1

Rear position (2) for revolution range between 0 - 2500 min

-1

Never shift the revolution ranges 1 and 2 during the

operation time. Within the revolution ranges 1 or 2 you can

execute smooth fine adjustment by using the revolution

selection switch (6).

Right revolutions/cutting speed

Setting the proper cutting speed can influence the machine

lifetime and working result significantly. It must be set according

to material you are working on. Right cutting speed will be

obtained by setting right revolutions.

Drilling

There is an empiric rule to be followed: the smaller holes there

are and softer the material is, higher are the revolutions.

Following table will help you with selection of right revolutions

for different materials. These revolutions data are only for your

orientation.

Ø drill Cast

iron

Steel Iron Aluminu

Bronze

3 2550 1600 2230 9500 8000

4 1900 1200 1680 7200 6000

5 1530 955 1340 5700 4800

6 1270 800 1100 4800 4000

7 1090 680 960 4100 3400

8 960 600 840 3600 3000

9 850 530 740 3200 2650

10 765 480 670 2860 2400

11 700 435 610 2600 2170

12 640 400 560 2400 2000

13 590 370 515 2200 1840

14 545 340 480 2000 1700

16 480 300 420 1800 1500

18 425 265 370 1600 1300

20 380 240 335 1400 1200

22 350 220 305 1300 1100

25 305 190 270 1150 950

(data in rev./min)

Milling

You can calculate the revolutions as follows:

n=v/(πxd)

n= revolutions in min

-1

v= cutting speed in v m/min

d= tool diameter in m

π= 3,14

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude GBF 550 - 48140 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info