Bedienungsanleitung Gude GESF 400 94569 (Seite 15 von 116) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch)

628771

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

Being careful prevents slipping or falling, especially when

reversing.

Safety operation instructions

Do not put your hands and legs near the rotating parts.

Keep a safe distance from the eject hole.

Be extremely careful when running over or removing snow

off brash entrances, footpaths and paths. Be prepared for

unexpected risks or moving vehicles.

When you hit a foreign item, switch the engine off,

disconnect the cable from the spark plug and check

thoroughly the snow blower for any damage and remove it

if necessary – the snow blower can be put into operation

again and worked with now.

If the appliance starts abnormally vibrating, switch the

engine off and search for the cause immediately.

Generally, vibrations are a warning against operating

failure.

Switch the engine off every time you stop operating the

appliance, clean the working screw/rotor can/eject tube

and when executing repairs, adjusting and inspecting the

appliance.

When cleaning, repairing and checking the appliance,

make sure that the working screw/rotor and all moving

parts are stopped. Disconnect the spark plug cable and

secure it in a way to ensure it cannot touch the connector

and cause unwanted engine starting.

Pull the cable out of electric motors.

Do not remove snow across slopes. Be extremely careful

when changing movement direction on slopes. Never try to

remove snow on steep slopes.

Never use the snow blower when guards, sheets and other

protection components are not installed properly.

Never use the snow blower near glass surfaces, cars,

windows, pits, etc.; set the eject tube angle properly.

Children and pets must be in a sufficient distance from the

appliance.

Do not overload the appliance; do not try to remove snow

too quickly.

Never use the appliance at a high travelling speed on a

slippery surface. Be careful when reversing.

Never aim the eject tube at bystanders. Do not allow

anyone to stand before the appliance.

Disconnect the working screw/rotor drive when the snow

blower is to be transported or when not being used.

Use only extensions and accessories approved by the

snow blower manufacturer (e.g. wheel weights,

counterweight, cabins, etc.).

The snow blower must only be used when appropriate

visibility or good lighting is provided. Stand fast on the

ground and hold the handle tight by hands at all times.

Walk, never run.

Do not allow anybody to stand on the appliance.

Use the snow blower only when appropriate visibility or

good lighting is provided.

Take all safety measures when leaving the appliance

unattended.

Stop the output shaft drive, lower the extensions, shift into

neutral, apply the parking brake, switch off the engine and

pull out the key.

Caution!

At less powerful networks there might be short voltage

fluctuations when the appliance is switched on. This may

influence the function of other appliances, e.g. there might

be light intensity fluctuations. Where there is network

impendance of Zmax < 0.997 Ω, these negative influences

need not be expected (more information can be obtained

from your local energy supplier if necessary).

Use as designated

The product you have bought (electric snow blower) has

exclusively been designed for the following range of use:

Proper removal of snow from private footpaths, entrances

and parking places unless they fall within the general road

traffic regulation (e.g. public footpaths or entrances; for

that, permit specific for the given country needs to be

requested from appropriate authorities if necessary).

Only fresh snow is used as the processed material.

Any other use is in conflict with the designation. The

manufacturer is not liable for any indirect damages and

injuries. Please be sure to know that our appliances have

not been designed for industrial use.

Installation

Caution! The appliance needs to be switched off and

unplugged before maintenance, cleaning and installation.

The same must be done if the feeder cable is damaged,

incised or entangled.

Respect the system voltage: current source voltage must

correspond to the details on the appliance type label.

An extension cable with a too small wire cross section

significantly reduces the appliance performance. For

cables within a length of 25 m at least 3 x 1.5mm²; for

cables of more than 25 m of length at least 2.5mm².

Caution! Extension cables not approved must not be used.

The extension cable, plug and clutch must be watertight

and approved for outdoor use.

Cable communications must be dry and must not lie on the

ground.

If a cable drum is used, it needs to be unwound.

Some parts of the snow blower are not installed when

being transported to the buyer.

Screws, manual wheels, cable clips and screwdriver can

be found in a separate plastic bag. Installation is simple if

instructions below are followed.

Eject tube

Take the appliance and all components out of the box.

Remove all the 4 screws on the front cover and the front

part (pic. 2). Now insert the eject tube to the front hole of

the cover. Then, using the 4 screws, mount the front part

to the cover and tighten the screws in a way to make sure

the eject tube is in a safe position that can be freely turned

by 180°. Finally, using the 2 supplied wing screws, mount

the upper return flap to the eject tube.

Lower upper of the sliding post

Pull the other end of the adjusting rodding (coming from

the eject tube) on the lower part of the sliding post and

then push the lower part of the sliding post down to both

cover holes (pic. 3). Make sure that both supporting

clamps clicked into the bottom end of the lower part of the

sliding post on the cover.

Upper part of the sliding post

Bring the cable pull strain relief equipment for the

extension cable to the upper part of the sliding post (pic.

4). Make sure the cable pull strain relief equipment does

not later get in contact with the 2-point safety switch to

prevent undesirable blocking (pic. 11). Now connect both

post halves and screw them to each other using the

supplied screws with manual wheels. The adjusting

rodding is used to change the eject tube direction.

Mount the 2-point safety switch to the upper part of the

sliding post, using two screws, to the appropriate hole

unless the switch is already assembled to the upper part of

the sliding post (pic. 6).

Gude GESF 400 94569 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info