Bedienungsanleitung Gude GGHA 4 in 1 95138 (Seite 12 von 72) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

626576

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Fitting the collection box

• Connect the canvas box to the metal frame (pic. 6)

and fasten it firmly to the metal frame (pic. 7) using

the plastic box clips.

• Open the rear cover and use the two hooks to

hang the collection box to the holding rod on the

cover (pic. 8)

Lawn dethatcher height calibration

• Adjust the lawn dethatcher height using the height

adjustment equipment (pic. 9).

• Turn the height adjustment equipment to the

required position and set an operating height that

is suitable.

Changing the blade shaft

• By simultaneous pressing down on both closures

you will open the front cover (pic. 1/8). (pic.10)

• To remove and insert the blade shaft,

pull the release. (pic. 11)

• Put the required extension to the shaft guide to the

right side.

Sweeping unit

• When fitting the sweeping unit, make sure the

metal part fits in its place (pic. 13 and 14)

Cutting unit

• When fitting the cutting unit, make sure both metal

parts fit in their place (pic. 15)

Dethatching unit

• When fitting the dethatching unit, make sure the

metal part fits in its place (pic. 17)

Aerating unit

• When fitting the aerating unit, make sure the metal

part fits in its place (pic. 18)

Starting the universal machine

• Before using the machine, make sure the blade or

its connecting elements are not damaged. Replace

any damaged blade if necessary.

• Before inspecting the machine, switch the engine

off and unplug the machine. To prevent

unintentional starting of the universal machine, the

2-point safety switch has been fitted with a safety

button that must be pressed before the starting

lever is pulled (pic. 19).

• When releasing the starting lever, the button must

be put to the original position.

• Make sure the extension cable is not within steel

spring reach. Press the safety switch and pull the

starting lever (pic. 19).

• Before starting your work, you must repeat this

step several times to make sure everything works

properly.

WARNING!!! You must necessarily wait until

the steel springs stop rotating and are idle in case

of any adjustment, servicing or repairs of your

universal machine. The universal machine must

necessarily be unplugged before these works.

Servicing and treatment

Pull the plug out of socket before every maintenance

and treatment! Maintain the appliance at regular intervals

(depending on the use frequency). Maintenance needs to be

strictly recorded.

• Make sure all fastening elements (screws, nuts,

etc.) are always tightened to ensure safe work with

the verticutter.

• Check the collection container more frequently for

signs of wear.

• Check the appliance regularly and replace any

worn-out or damaged parts.

Use a damp cloth to clean the plastic parts. Do not use

cleaning agents, solvents and pointed items.

Remove any dust and dirt from the machine after using it.

Empty the dirt container.

Beside this, no servicing is needed to be performed on the

machine.

Cleaning

Keep the guards, ventilation slots and engine case with no

dust and dirt if possible. Wipe the appliance with a clean

cloth or blow it with compressed air under low pressure.

Cleaning the appliance immediately after each use is

recommended. Clean the appliance regularly with a wet cloth

and a bit of liquid soap. Do not use cleaning agents and

solvents as they could damage plastic parts of the appliance.

Make sure no water gets inside the appliance.

Adjusting the cutting mechanism (pic. 17)

The cutting mechanism of your universal machine has been

adjusted to optimum before leaving the factory. If the mower

is not cutting smoothly after it has been used for a long time,

please fix the bottom blade adjustment.

Test cutting

Put a slip of paper on the bottom knife so as it points to the

knife roller axis. Turn carefully the knife roller. If the bottom

knife is adjusted properly, the paper will be cut off as if

scissors are used. Repeat the test cutting for various knives.

Right cutting

To have a well-kept lawn, we recommend cutting grass at

regular weekly intervals if possible. Grass thickens by

frequent cutting. If the grass has not been cut for a long time,

cutting should first take place in one direction with the

highest cutting height and then across with the required

cutting height. The maximum length of blades is 12 cm to be

able to be cut by the reel mower. Cut only dry grass if

possible as wet grass does not provide fine cutting.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude GGHA 4 in 1 95138 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info