Bedienungsanleitung Gude GH 650 B 94360 (Seite 20 von 69) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

627490

Zoom out

Zoom in

Vorherige Seite

1/69

Nächste Seite

Discharge outlet and crushing screen cleaning

Remove the lid for discharge outlet maintenance: screw out the

through-bolt and remove it along with the case (pic. 24).

Loosen the top and external wing nuts and unhook the lid.

Tip the crushing screen down by screwing out the wing nuts (pic.

25) and clean the discharge outlet.

Always use safety gloves! The hammer mechanism knives

are very sharp! Use eventually a rod or other tool that cannot

damage the knives.

Maintenance of knives

To turn the cutting knives, you must first remove the socket plug

(engine is cooled down).

Disassemble the lid for discharge outlet maintenance as

described in the above article (pic. 24/25/26).

Then, after screwing out the check nuts, remove the lid of outlet

for crushing knives maintenance (pic. 1 note 9). Now you can see

into the knife disc. Now you must place the crushing knives in

front of the maintenance outlet. To do so, remove the crushing

screen so that the knife disc could turn on the outer side of the

hammer mechanism.

Remove the cotter key on the crushing screen axis (pic. 26) –

arrow.

Pull out the axis with the case (pic. 27 – arrow) and remove the

crushing screen.

Now CAREFULLY turn the hammer mechanism (use safety

gloves)

Pic. 21a shows the position at which knives can be disassembled.

ATTENTION: The knives are extremely sharp!

Loosen the holding screws and turn the knives by 180°.

Make sure the knives are fitted well again.

If the knives are blunt, you can have them sharpened at a

specialist or replaced with new ones.

Cleaning in general

Lubricate all movable parts with oil and safely re-fix all removed

parts after each cleaning.

Clean the engine with a rag. Avoid sprinkling with heavy water

current as water can get to ignition, fuel system and lubricant

system and cause failures.

Air filter and fuel screen cleaning

The air filter must be cleaned every 20-30 running hours. Remove

the air filter cover by screwing out the wing nuts (pic. 17a - arrow)

and pull out the air filter insertion.

Clean the filter with benzoline. Drop a few drops of motor petrol

on the filter after cleaning. Assembly in the opposite order.

Clean the fuel screen by removing the tank cover and pulling out

the screen (pic. 18a). The screen can carefully be blown-dry.

Transport and storing

The appliance can only be transported when the engine is off.

Clean the appliance thoroughly before storing.

Store the appliance at a clean and dry place with no fuel in the tank.

Storing

If the crusher is not used for a longer period of time, the following

works need to be executed:

Thorough cleaning and repair of the damaged varnish.

Sprinkle the movable and stressed parts with anti-corrosive oil.

Crusher shutdown and storing

Do not store the crusher in wet rooms, in rooms with fertilisers, in

stables and adjacent spaces.

At tipping, the motor oil can get to the combustion space and thus

cause problems at starting or oil carbonisation.

Risk of strong corrosion creation.

Failure - Causes - Removal

Failure Cause Removal

Jammed

crushed

material

1. Blunt knife 1. Sharpen or turn the knife

Output

drops

1. Jammed

crushing

mechanism

1. Switch off the appliance and clean it

Engine does

not start

1. Empty tank

2. No ignition

spark

3. Engine with

excessive

consumption

4. Blocked

knife

5. Lack of oil

protection

1. Fill up full tank; check whether the

carburettor contains fuel;

Check tank vent pipe and perforate

the hole in the tank cover with a

needle

2. Clean the ignition spark and keep

the distance of electrodes at 0.6 –

0.8 mm (pic. 19 a) or use a new

one;

Check the ignition cable;

Have the ignition checked at a

servicing centre

3. Screw out the sparking-plug, clean

and dry it;

Pull the starter cable several times

while the sparking-plug is screwed

out

4. Make sure that the crushing

mechanism was not blocked.

5. Please check carefully the oil level

and add motor oil again. Place the

unit in a horizontal position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude GH 650 B 94360 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info