Bedienungsanleitung Gude HPC 200 86001 (Seite 10 von 49) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

628589

Zoom out

Zoom in

Vorherige Seite

1/49

Nächste Seite

General guidelines

 Ensure proper water supply before turning on the high-pressure

 cleaner. Pump dry run causes major damage to the gasket system.

 Do not unplug the power plug by pulling on the power cord.

 In winter, the high pressure cleaner must be stored in a frost-free location.

 The cross-section of the extension cords used must correspond to the cord length, e.g. a longer extension cord

must have a larger cross-section, and vice versa. In addition, protection class “IPX5” extension cords must be

used. See the following table for additional details.

 Clean water intake filter regularly!

Voltage

Volt

Extension up to 25 m Extension up to 50 m

MOTOR

220 -230

240

Cross-section 3x1.5mm² Cross-section 3x2.5mm²

 Set-up the high-pressure cleaner near the water source.

 The packaging elements can be recycled, and consequently they must be disposed of according to the state-specific

guidelines.

 The high-pressure cleaner may only be operated with the accessories and replacement parts recommended by the manu-

facturer. The use of original parts (accessories and replacement parts) assures safe and problem-free operation of the

high-pressure cleaner.

 The high-pressure cleaner must be placed on a safe and stable substrate.

 The high-pressure cleaner is designed exclusively for cleaning vehicles, machines, boats, buildings, etc., and for removing

stubborn grime with clean water and biodegradable cleaning agents.

 The high-pressure cleaner is intended for private use only; it is not intended for professional use (industry, commercial).

 Cleaning vehicles is only permitted in facilities with oil separation.

Installation

 Connect the HP gun to the high-pressure hose.

 Connect the high-pressure hose to the water discharge of the high-pressure cleaner.

 Connect the water supply hose to the water input of the high-pressure cleaner. The hose diameter must be at least 13 mm;

the hose itself must be reinforced.

 The temperature of the out-flowing water may not exceed 50 UNDER ANY CIRCUMSTANCES. The water pressure

may NOT exceed 10 bar.

 ATTENTION: The high pressure cleaner should be operated with clean water.

 Switch the motor switch to “ON”.

 The power outlet intended for connecting the high-pressure cleaner must correspond to the voltage and frequency (V/Hz)

specified on the nameplate.

Observe the rules of your water supply company.

Eventuel you need to install a backflow preventer to prevent the backflow into the drinking water network (cleaning

agents).

Use

Open the water line cock COMPLETELY.

Unlock gun, open it and leave it in this condition for several seconds to vent as well as to blow off residual pressure

from the lines.

Start the motor with the switch when the gun is open.

The gun must be opened when switching the motor on again.

If the pistol is open, then the drop in pressure automatically starts the motor. The pressure is restored with a minimum delay.

USING CLEANING AGENTS: Connect the foam injector container with cleaning agent on the spray tube. Then apply the suc-

tioned-in cleaning agent mixed with water.

After concluding the work:

 Switch-off the high-pressure cleaner.

 Close water cock.

 Discharge residual pressure from the gun, until all the water has escaped from the adjustable nozzle head.

 Unplug the plug from the power outlet.

Maintenance

Attention: Always unplug the high pressure cleaner from the power source before performing any work on the unit.

For problem-free function of the high-pressure cleaner, check and clean the suction filter after every 20 hours of operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude HPC 200 86001 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info