Bedienungsanleitung Gude HWW 1000 IE (Seite 12 von 44) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

628566

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

If the pump is used for ponds, wells etc. and in corresponding

water equipments, the standards applicable in the countries where

the pump is used shall be unconditionally observed.

Electric pumps used outside (e.g. at the ponds etc.) shall be

furnished with rubber electric cable type H07RNF, according to

standard DIN 57282 or. DIN 57245.

When the pump is in operation, no people or animals are

allowed to stay or dive in the liquid being repumped (e.g.

in swimming pools, in cellars etc.).

The repumped liquid temperature shall not exceed +35 °C.

Should extension cables be used, they shall be made

exclusively of rubber, type H07RNF, according to standard

DIN 57282 or DIN 57245. The pump connected to the

electric network shall never be touched by a cable, never

lifted by holding the cable or transport by means of a cable.

The connecting socket shall always be in necessary

distance from water and moisture and the plug shall be

protected against moisture.

Before putting the pump into operation check if the electric

cable and/or the socket are not damaged.

Before performance of any works on the pump the plug

shall be pulled out of the socket..

If the pump is built-in in a gully, the gully shall be covered

with cover to ensure the safety of people walking there.

The pump shall never be installed in moist shifts

(danger of shortcut, damage caused by corrosion)!

For avoiding or prevention of possible damage (as e.g.

flooding the rooms etc.) due to faulty pump operation

(e.g. due failure or defects) the owner (user) shall take

reasonable safety measures (installation of alarm

equipment, a spare pump etc.)

In case of failure on the pump,. the repair shall be

performed exclusively by an authorized service

repairshop.Only original spare parts may be used.

We have to draw your attention to the fact that

according to the valid standards we cannot take

responsibility for below mentioned cases of possible

damage caused by our devices:

Unproper repairs performed by unauthorized service repair

shops;

Using pump for a different purpose or failing to observe its

use according to the provisions;

Overloading of the pump by long-term operation.

Protection against Thermal Overloading

A sensor is built into the engine that automatically switches off

the pump if a certain temperature has been exceeded, and/or

it switches the pump on after it has been cooled. This

increases the service life of the pump quadruptly, and

prevents burning of the electric engine.

Protection against Overloading /Thermoswitch of the Engine

The pump is furnished with an engine thermoswitch. If the

motor is overheated, the thermoswitch switches the pump

automatically off. The cooling period makes approx. 25

minutes, thenafter the pump will be automatically switched

on again. If the engine switch is on, it is necessary to find

and remove the cause (see also “Troubleshooting”). The

data here given cannot be considered as instructions for

“home made” repairs, because the repair works require

specific professional knowledge and skill.

Therefore you have to contact customer service if any

failure occurs.

It is unconditionally necessary to secure good air

supply in order to prevent overheating of the pump!

Do not install the pump in too tight shifts, do not cover

it with anything!

Operation

Pull out the network plug.

Filtermontage (Filter nicht im Lieferumfang enthalten!)

Montage (siehe Abb. E)

Flussrichtung beachten

Gewinde abdichten (siehe Abb. B)

Beim Auffüllen Entlüften (Abb. C/E)

Max. Druck 5 bar

Vor Frost schützen

Filter regelmäßig mit Bürste und klarem Wasser reinigen

Air pressure

Open the consumption valve, e.g. water main tap, so that the

water may be pressed out of the system.

Turn the protection lid on the bleeding valve in the down

direction (F).

Check the air pressure in the vessel with compressor and

device for tyre pumping.

The specified air pressure is 1,5 ± 0,3 bar.

Bleeding

Release the bleeding screw and let the possible closed air

escape. (Fig. A; pos. 2)

Water Bubbles

Release the screw for draining water bubbles so that the

pump may be drained (Fig. A; pos.11)

Vessel pressure

Switch off pressure set by the manufacturer is 3-4 bar after

completion of filling.

Setting pressure of the vessel (air) makes 1,5 ± 0,3 bar and it

should be regularly checked and modified (G).

Safety Instruction for Operator

Use the device only after you have carefully read Operating

Manual.

Observe all safety instructions mentioned in the Manual.

Behave responsibly against other persons.

Instruction Step-by-Step

 Connect the suction pipeline that complies with the

outlet connecting pipe to the check valve (C)

(foot

valve). Tighten all

threading connections by sealing

band (B)

 After filling up remove the bleeding screw . (Fig. A;

pos. 10) on the back side of the pump and on the

connecting line of pressure pipeline. (Fig. A; pos. 1

and 2) Fill the device up until the water exits from

the bleeding hole (E)

 Make tight the bleeding screw and retight it again.

Then make tight the pressure pipeline and connect

it.

 Connect the pump to the electric network.

Caution: When installing suction and pressure

pipeline on corresponding connection lines, the

corresponding thread shall always be tightened

carefully so that no damage occurs due to cracking of

the pump shell (A) !

Caution: Careful sealing of thread connections

(A/B) and airless

filling (E) of suction system – (suction

hose and pump shell) , will save you from trying to

perform suction that may often be unsuccessful!

Check the tightness of the foot valve (D) – Fill the

system according to the instruction (C) and pull the

Gude HWW 1000 IE Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info