Bedienungsanleitung Gude HWW CAB 200-100-400 V 94193 (Seite 12 von 67) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Schwedisch)

628565

Zoom out

Zoom in

Vorherige Seite

1/67

Nächste Seite

We have to draw your attention to the fact that

according to the valid standards we cannot take

responsibility for below mentioned cases of possible

damage caused by our devices:

Unproper repairs performed by unauthorized service repair

shops;

Using pump for a different purpose or failing to observe its

use according to the provisions;

Overloading of the pump by long-term operation;

Protection against Thermal Overloading

A sensor is built into the engine that automatically switches off

the pump if a certain temperature has been exceeded, and/or

it switches the pump on after it has been cooled. This

increases the service life of the pump quadruptly, and

prevents burning of the electric engine.

Protection against Overloading /Thermoswitch of the

Engine

The pump is furnished with an engine thermoswitch. If the

motor is overheated, the thermoswitch switches the pump

automatically off. The cooling period makes approx. 25

minutes, thenafter the pump will be automatically switched

on again. If the engine switch is on, it is necessary to find

and remove the cause (see also “Troubleshooting”). The

data here given cannot be considered as instructions for

“home made” repairs, because the repair works require

specific professional knowledge and skill.

Therefore you have to contact customer service if any

failure occurs.

It is unconditionally necessary to secure good air

supply in order to prevent overheating of the pump!

Do not install the pump in too tight shifts, do not cover

it with anything!

Operation

Air pressure

Pull out the network plug.

Open the consumption valve, e.g. water main tap, so that the

water may be pressed out of the system..

Turn the protection lid on the bleeding valve in the down

direction (F).

Check the air pressure in the vessel with compressor and

device for tyre pumping.

The specified air pressure is 1,5 ± 0,3 bar.

Bleeding

Release the bleeding screw and let the possible closed air

escape. (Fig. A; pos. 2)

Water Bubbles

Release the screw for draining water bubbles so that the

pump may be drained (Fig. A; pos.11)

Vessel pressure

Switch off pressure set by the manufacturer is 3-4 bar after

completion of filling.

Setting pressure of the vessel (air) makes 1,5 ± 0,3 bar

and it should be regularly checked and modified (G).

Safety Instruction for Operator

Use the device only after you have carefully read Operating

Manual.

Observe all safety instructions mentioned in the Manual.

Behave responsibly against other persons

Instruction Step-by-Step

• Connect the suction pipeline that complies with the

outlet connecting pipe to the check valve (D) (foot

valve). Tighten all threading connections by sealing

band (B)

• After filling up remove the bleeding screw on the

back side of the pump and on the connecting line of

pressure pipeline. (Fig. A; pos. 1 and 2) Fill the

device up until the water exits from the bleeding

hole (Fig. A; pos. 2). (E)

• Make tight the bleeding screw and retight it again.

Then make tight the pressure pipeline and connect

it.

• Connect the pump to the electric network.

Caution: When installing suction and pressure

pipeline on corresponding connection lines, the

corresponding thread shall always be tightened

carefully so that no damage occurs due to cracking of

the pump shell (A) !

Caution: Careful sealing of thread connections

(A/B) and airless filling (E) of suction system – (suction

hose and pump shell) , will save you from trying to

perform suction that may often be unsuccessful!

Check the tightness of the foot valve (D) – Fill the

system according to the instruction (C) and pull the

suction hose out of the medium being repumped before

putting into operation for the purpose of checking (D) -

the liquid should not escape from the suction hose

now!

Important: Should the pump be out of operation for a longer period of time, the pipeline and the pump shell must be

unconditionally emptied.

Troubleshooting

CAUTION: FIRST OF ALL CHECK ALWAYS THE FUSES AGAINST OVERLOADING!

Failure Cause How to remove the failure

Engine cannot be

started.

No nework voltage.

Pump wheeel is blocked.

Check the voltage.

Turn the engine shaft with screwdriver through the fan

cover (to release friction circles sealing that may be

stuck together)

The pump does not

suck

Missing, untight or blocked foot valve

Foot valve is not in water.

No water in the pump shell.

Too high suction height.

Air bubbles in suction pipeline.

Connections not sealed, the pump sucks the air,

the pump is not bleeded.

Assembly or clean the foot valve.

Immerse the foot valve into water.

Fill the pump shell with water.

Check the suction height.

Check the tighting of suction pipeline.

Carefully repeat connection according to chapter

„Putting into Operation“!

Insufficient quantity of

water to be repumped.

Too high suction height.

Foot valve suction basked dirty

Check the suction height.

Clean tne suction basket.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude HWW CAB 200-100-400 V 94193 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info