Bedienungsanleitung Gude MS1600 3 IN 1 (Seite 17 von 24) (Deutsch, Englisch)

626211

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

 Never adjust the height of wheels when the engine is

running.

 The grass catching device may lose its functioning any

throw away items due to wear or damage. Regularly

check the mower parts and, if necessary, replace them

with spare parts recommended by the manufacturer.

 The mower knife is very sharp. Risk of injury! Be

especially careful at knife maintaining, wear protective

gloves or cover the knife-edges.

 Do not change the basic engine adjustment and avoid

its overloading.

 Be especially watchful when turning the mower or

pulling it towards your body.

 If it is necessary to incline or lift the mower to pass a

surface other than grass or when carrying the mower to

or from the area to be cut then cut off the knife.

 Release the knives and engine clutches before

switching on.

 Start the engine in accordance with the operating

instructions and make sure your legs are in safe

distance from the knife.

 Do not incline the mower at starting except for cases

when it is necessary. Do not incline the mower more

than necessary in such a case and always lift the part

reversed from you.

 Do not start the engine when standing in front of the

ejection outlet.

 Never lift and transfer the mower with engine running.

 Lower the brake adjustment when the engine is off. If

the engine is equipped with a stop valve then close the

petrol supply after cutting.

 Move slowly if using an auxiliary trail seat.

ASSEMBLY / PREPARATION

All assembly and/or maintenance works may be

performed only when the motor is turned off!

Please read the entire operating instructions before

assembling or starting your new mower.

IMPORTANT: The mower is supplied without oil and

petrol.

Lawn mower unpacking

Take the lawn mower out of board and make sure there are

any free parts left in the package.

Assembly - handle

IMPORTANT: Carefully assemble the handle so that cables did

not get tangled or damaged.

Assemble the handle according to pictures 3 to 7 and use the

assemble elements from picture 2 to this purpose.

Fixing – collecting bag

IMPORTANT: The collecting bag must fit in and be secured

with a safety loop on the middle part of the sliding handle.

Refuelling

Refuel in mixing ratio of 40:1 for two-stroke engines. Please

use only high-quality fuel for two-stroke engines.

Cartridge replacement

You can choose from three various cartridges:

pic. 3 pos. 4 = spindle cutting mechanism

pic. 3 pos. 5 = aerator cartridge

pic. 3 pos. 6 = ventilator cartridge

The appliance needs to be turned upside down before

cartridge replacement (pic. 8)

Cartridges are inserted in appliance fixtures (pic. 10 pos. A

and B) by pressing the fixing casings (pic. 9). Fixing screws

(pic. 10 pos. D) must safely fit in the fixtures

(pic. 10 pos. C). See pic. 11.

Height adjustment

The axle needs to be adjusted for setting the working height.

To this purpose, put both axle ends to an identical screening

position by pulling and snapping. See pic. 13

Maintenance instructions

Air filter (pic. 14 pos. a)

Make sure the air filter insert is always clean – clean it with

benzine if necessary.

Distance of spark plugs

The spark plug must be 0.7-0.8 mm from the electrode (pic.

15)

Use original spark plugs!

Operation

The lawn mower is automatically driven and needs to be lifted

in the front part by smooth pressing of the sliding handle when

reversing and being converted.

Watch for thrown-away parts of the work insertion!

Storing

It is recommended to screw the spark plug out and add two oil

drops in a two-stroke engine cylinder at longer storing to

prevent cylinder and piston corrosion (pic. 16).

General instructions for spindle cutting

Cut grass whose maximum height corresponds to half

diameter of the spindle. If for example the spindle diameter

is 16 cm the grass height should be max. 8 cm – or less

would be best.

Spindle cutting needs to take place at least once a week and

more often in the growth time. Early in the morning and when

dew is still present is the right time for spindle cutting. The

grass cut height needs to be slowly reduced after conversion

from sickle cutting to spindle cutting so that grass blades had

time to adapt. The cut grass should immediately be removed

from the grass plot. If it is left in lumps or a too thick layer the

grass can get sick. Removing prevents from these diseases.

The ideal cutting height for the spindle mower is 1.5 cm.

ATTENTION: There must be no hard items (stones, etc.)

on the surface!

Foreign items can damage the cutting spindle!

(paid service)

General instructions for loosening and aerating

Time and work steps:

You can either aerate or loosen depending on the moss layer

thickness. The best time for loosening and aerating is spring.

However, the soil must not be too wet and the grass should

constantly and regularly grow well and be dry. Loosening can

take place even after second or third grass cutting.

Cut the grass shortly one more time if necessary and remove

it. An aerator is used strip by strip, not overlapping each other

much. The material is collected and removed again. An

aerator is used again – however, crosswise to the first

passage this time. The waste is removed from the grass plot.

ATTENTION! First try as low working depth as possible!

Maximum loosening depth –15 mm

Maximum aerating depth–10mm

 Starting

1. Press the primary pump 3-5 times so that the fuel gets in the

carburettor (when the engine is cold only) (pic. 17)

2. Close the starting valve (pic. 19 pos. 0)

3. Press the operational lever to the sliding handle (pic. 12

pos. I)

4. Shift the gas lever slightly forward (pic. 20) and evenly pull

the starter cable until the engine starts. Always let the

starter cable slowly slide back to prevent damage to the

reverse starter (pic. 21).

5. The engine should run smoothly after some time. The

starting valve can be opened again (pic. 18). Put the gas

lever to the desired position of revolutions and start

working.

ATTENTION

The mower moves forward quicker each time the gas is turned

up!

Gude MS1600 3 IN 1 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info