Bedienungsanleitung Gude PERSLUCHTAPPARATEN SET (Seite 9 von 60) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

622218

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Please read carefully the following Operating Instructions before putting the appliance into operation

A.V. 2 Any reprints, even partial, are subject to approval. Technical changes reserved.

Illustrative pictures! Translation of original operating instructions.

Do you have any technical questions? Any claim? Do you need any spare parts or operating instructions?

We will quickly help you and without needles bureaucracy at our web pages at www.guede.com in the Servicing part. Please help us be able

to help you. In order to identify your device in case of claim we need the serial No., product No. and year of production. All this data can be

found on the type label. Please enter it here for future reference:

Serial No.: Order No.: Year of production:

E-Mail: support@ts.guede.com

General

Dear Customer

Thank you for your confidence in our products and us. By buying a Güde product you have decided to buy a quality product that

corresponds with the present safety standards.

Please read carefully the operational manual before you start using your tool. Once you have read and understood the manual, only

then start using your tool. The manual includes important instructions that are necessary for safe and trouble free operation of your

tool. Please store it near to the tool.

Operational and safety instructions

Pneumatic tools work with working pressure of different values. The recommended work pressure amounts to 6 bars

for most machines when idle or when at standstill.

Higher pressure would result in shortening the service life of your machine due to heavy load.

Water in the compressed air inlet can damage the machine. Therefore it is necessary to remove the water from the

compressor or piping on regular basis! The air filter should be cleaned at least once a week.

Güde pneumatic tools start up and maintenance

During the development of our pneumatic tools we worked on the assumption that it is necessary to construct them in such a

way so that they could be run with relatively low air consumption. Güde pneumatic tools can be run, under certain

circumstances, by a Güde compressor with the suction capacity starting at 230 litres. The ideal capacity is provided by

compressors with the suction capacity of 300-400 litres. Therefore, we would recommend Güde compressors, series

300/11/40, 400/11/50, 400/11/60, 600/11/60, 600/11/90 and bigger compressor stations, to be used with this set of pneumatic

tools.

In particular we would recommend Güde compressor 631/10/90, 380 V, 10 bar. All Güde pneumatic tools can be

operated with this compressor without any limitations.

The following points must be observed before starting to use the pneumatic tools.

1. Pneumatic tools should be operated only with the lubricating device on.

2. A pressure reducing valve must be on the compressor (all Güde compressors are equipped with a reducing valve).

3. Fit a water separator (filter) before the lubricating device.

4. Maximal operating pressure of the pneumatic tool is 6 bars. If you set the reducing valve at value higher than 6 bars, the

pneumatic tool can get overloaded.

5. If there are longer breaks in operation, we would recommend you should thoroughly clean and lubricate the pneumatic

tools with oil. When starting to run it again add a bit of oil into the pneumatic tool connector, and then use it with the

pneumatic lubrication equipment on. Some machines are equipped with a smooth regulation of revolutions and impact

power (etc. an impact fastener, a drill with left or right hand rotation, a set of chipping hammers, an eccentric grinder, a

hand vibration grinder etc.). This control screw is located directly next to the tool air connector.

6. For the Güde pneumatic impact fastener we would recommend to use only hardened detachable Güde nuts. You should be

able to purchase them in any good specialized shop. This is valid for chipping hammers of various sizes and Güde

pneumatic chipping hammer.

We hope you will enjoy working with your new tools. Please notice our guarantee provisions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude PERSLUCHTAPPARATEN SET Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info