Bedienungsanleitung Gude Pro 6500 PRO 75840 (Seite 10 von 55) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

629070

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

Residual Hazards and Protective Action

1. Mechanical Residual Hazards:

• Catching, winding:

Lose garments and jewels may be caught with moving

parts.

Contact with rotating sander disk may result in serious injuries.

• Friction, abrasion:

Always wear tight-fitting garments and do not wear

jewels that might be caught.

Avoid any contact with the sanding means. Use protection

gloves.

2. Electrical Residual Hazards:

• Direct electrical contact:

Defective cable or plug may cause an electrical shock.

Have the defective cable/plug exchanged by a professional.

Use the unit only if connected via a faulty current switch (FI).

• Indirect electrical contactt:

Accidents caused by conductive parts on open or

defective structural parts .

Always unplug for maintenance Use the unit only if connected

via a faulty current switch (FI).

3. Noise Hazard:

• Hearing Impairment:

Prolonged work with the unit may result in hearing

impairment.

Wear ear protectors

4. Materials and Other Substances Hazards:

• Contact, aspiration:

Lungs may be affected by great amount of dust being

formed.

Always wear breathing mask when working with the unit.

5. Human Factor Neglect:

• Neglect us of personal protection equipment:

Operating the unit without adequate PPE may cause

severe external/internal injuries

Always wear prescribed protective clothing and work

considerately.

• Inadequate local lighting:

Insufficient light is a heavy safety risk.

Provide for sufficient lighting

6. Other hazards:

• Thrown away objects and splashes:

In the process of cutting, the blade or mechanical

particles may injure your eyes.

Always wear goggles when working with the unit

Assembly and Initial Operation (Fig. 2)

Mount the unit to four respective points on flat horizontal

ground using suitable screws and check it for firm settlement.

Workbench Alternative Assembly (Fig. 1 and 3)

Fig. 1:

Belt and disc grinding machine 6500 PRO is supplied nearly

completely assembled. It is only needed to shift the table

bracket (Fig.1 – pos. 3) to a given screw and to screw it

together with an socket wrench.

Fig. 3:

Now, attach the table bracket with the lock screw delivered.

Now, the table is smoothly adjustable.

Initial Operation Safety Instructions

• Mind the safe attachment of the unit on a suitable surface

area.

• Make sure that all the screwed joints are tight.

Procedure

• The assembly of parts should be done in shown order. Be

particular about correct arrangements of structural parts

according to the figures.

• Connect a suitable dust exhauster to the exhaust

connection.

The unit must always be operated with a dust

exhauster. That will prevent excessive dust nuisance

that may be health hazardous and helps to a better

sanding result.

Operation (Fig. 4 and 5)

Fig. 4:

Mind the run direction!

Fig. 5:

By pressing button (I), the unit will switch on. Pressing button

(0), it will switch off.

Change of Grinding Angle (vertical use, Fig. 6,7 and 8)

Use the Allen key to loosen the screw(s) beyond the abrasive

wheel (size 6 mm) equipment  (Fig. 6).

Set up the required angle of the grinding belt.

After setting the required angle, retighten the screw (Fig. 7)

Now, the unit is ready to work with the grinding belt fitted

vertically (see Fig. 8).

Operator Safety Instructions

Unplug before any maintenance, adjustment and

cleaning. Unplug, having finished the work.

• Do not use the machine until you have read the

instruction manual carefully.

• Observe any safety instructions included in the

manual.

• Be responsible to the others

Step-by-step Instructions

1. Switch on the unit and work the piece either on the

sander belt or the sander disk. (Never work it against the

run direction)

2. Switch the unit off and clean it.

Troubles – Causes – Troubleshooting

(Trouble): Burnt wood.

(Cause):

1. Blunt belt or disk.

(Troubleshooting):

1. Replace the belt/disk.

(Trouble): Belt running sideward.

(Cause):

1. Set-up does not match.

(Troubleshooting):

1. Set-up the belt again

(Trouble): Belt will not start up.

(Cause):

1. Belt too tensioned

(Troubleshooting):

1. Loosen the belt.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude Pro 6500 PRO 75840 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info