Bedienungsanleitung Gude Pro GDS 16 PRO 55097 (Seite 12 von 82) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

629068

Zoom out

Zoom in

Vorherige Seite

1/82

Nächste Seite

Before operation

• All covers and safety equipment must be properly

installed before putting the appliance into operation.

• The saw blade must run freely.

• It is necessary to pay attention to undesirable items

such as nails, screws, clamps in already processed

wood. (Remove them if necessary).

• Before pressing On/Off, make sure the saw blade has

been fitted properly and the saw blade tension is

adjusted as it should and the moving parts are

running smoothly.

• Before connecting the appliance, make sure the

details on the type label correspond to the system

details.

Appliance to be used with RCD (safety switch

against stray current) 30mA only!

Installation

Please make sure the appliance is installed evenly and

steadily on a solid surface with adequate lighting.

Make sure you have enough room to work safely and

undisturbed.

Residual risks

The appliance has been designed according to the state of

the art and

recognised safety-technical regulations. However, there

still may be some residual risks when working with the

appliance.

• Risk of injury for fingers and hands by the saw blade.

• Risk of injury by throw-away workpieces in case of

unprofessional guidance.

• Risk of electric shock when unspecified feeder cables

are used.

• Never look directly to the laser.

• Further, there may be some hidden residual risks

despite all the preventive measures taken.

• Residual risks can be minimised if Safety

instructions and Use as designated and the entire

Operating Instructions are followed.

Plugging

Check regularly the feeder cables for any damage. Before

that, the appliance must be unplugged!

The feeder cable must be in accordance with applicable

provisions of VDE and DIN. Feeder cable with H 07-RN

marking to be used only. Sticking the type marking on the

feeder cable is mandatory.

Defective feeder cables

Insulation gets often damaged on the electric feeder

cables.

Possible causes:

Galls if feeder cables are guided in gaps under windows or

doors.

Breaks as a result of unprofessional fixing or guiding of

feeder cables.

Cutting-off as a result of the feeder cable being run over.

Insulation damage by pulling the cable out of wall socket.

Cracks as a result of insulation aging.

Feeder cables damaged in this manner must not be

used – they are a risk to life due to the insulation

damage!

Operation

• The saw does not cut wood automatically. The user

enables cutting by guiding wood to the moving saw

blade.

• Teeth cut the wood only when down.

• Wood must be guided slowly to the saw blade as the

saw blade teeth are very small.

• Every person needs some time of training to handle

the saw. During that time, several blades will certainly

get broken.

• When cutting thicker pieces of wood, it is especially

necessary to make sure the saw blade is not bent or

turned. This will increase the life of the saw blade.

• Best results are achieved with wood thinner than 20

mm.

The right saw blade

Small and narrow saw blades must be used for thin wood

not thicker more than 6 mm.

Wider saw blades must be used to cut wood thicker than 6

mm.

With wider saw blades it is not possible to cut small and

narrow curves as with thinner saw blades.

The saw blade gets worn more when processing plywood,

hard wood and thick pieces of wood (from 19 mm).

Switching on/off - pic. E

To switch the appliance on, press the green button (pic.

E/14).

To switch the appliance off, you must press the red button

(pic. E/15).

Caution: The appliance has been fitted with a

safety switch against repeated switch-on after power

failure.

Speed controller - pic. E

With the stroke number controller (pic. E/13) the number of

strokes (saw blade running speed) can be set depending

on the cut material.

E.g. the lowest setting of 400 per min.

-1

and highest setting

of 1,600 per min.

-1

for soft materials and materials with

long fibres.

Performance of inner cuts

1. The fretsaw characteristic includes performance of

inner cuts in the board with no damage to the board

outer side or circuit.

Caution: To prevent injuries due to accidental start of

the appliance, the appliance must always be unplugged

before removing or changing the saw blade.

2. To perform inner cuts in the board: Remove the saw

blade as specified under Changing the saw blade.

3. Drill a hole of app. 6.3 mm in the given board.

4. Put the board with the hole on the saw bench over

the inlet.

5. Fit the saw blade through the hole in the board and

adjust the blade tension.

6. After performing the inner cuts, remove the saw blade

from the holders (as specified under Changing the

saw blade) and take the board off the bench.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude Pro GDS 16 PRO 55097 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info