629054

Gude Pro PRS 700 75772 Seite 14

14
Zoom out
Zoom in
Vorherige Seite
1/80
Nächste Seite
Safety instructions for the operator
CAUTION !!!
THE ENGINE MAKES A GROWLING NOISE WHEN THE
MACHINE IS BEING STOPPED AND SHORTLY AFTER
HAVING STOPPED.
AT THIS POINT, THE SWITCH MUST NOT BE PRESSED
IN ANY CASE. (NEITHER ON NOR OFF). THE ENGINE
MAY BE SWITCHED ON AGAIN AFTER THE
GROWLING NOISE HAS VANISHED. DO NOT SWITCH
THE MACHINE ON AND OFF MORE THAN 6 TIMES PER
HOUR.
Please check the circular-saw blade rotation direction at
the time the blade is being started up.
The rotation direction is correct is the circular-saw blade
teeth are rotating towards the operator.
If the rotation direction is incorrect, the rotation
direction must be changed by switching the two
switchable plug poles by turning them using a
screwdriver with slight pressure. (see First putting into
operation)
Residual risks and protective measures
Even when used in accordance with the designation and
following all applicable safety provisions, there still may be
some residual risks, depending on the machine design.
Residual risks may be minimised if provisions of the
"Safety instructions", "Use as designated" and the
Operating Instructions are respected.
Discretion and caution minimise the risk of injuries of
persons and damage.
• A contact with the circular-saw blade in an exposed
part of the saw.
• A contact with the rotating circular-saw blade.
Risk of injury to fingers and hands by the tool
(circular-saw blade) or material being cut, e.g. when
changing the circular-saw blade.
• Injury by thrown-away parts of the material being cut.
• Backlash of the material being cut or parts of the
material being cut.
• Circular-saw blade breaking or shooting out.
• Risk of electric shock if defective electric cables are
used.
• A contact with conductive parts at exposed electric
construction parts.
• Hearing damage caused by long work without hearing
protectors.
Further, there may still be some hidden residual risks
despite all the preventive measures taken
Changing the circular-saw blade
1. Loosen the table protection (pic. 4) on both sides. 4).
2. Now shift the table fully to the front so that the
protective cover (pic. 5) is put on the circular-saw
blade to the full extent. 5).
3. Now the table can be folded back (pic. 6).
4. Now dismount the circular-saw blade as shown in
pictures 7-12 and refit a new one in the reverse
order.
Do not forget to hook on the table protection again
after finishing your work!
Transport and storage
Unplug the machine before any transport.
To ensure trouble-free transport, pull out the two travel
handles (pic. 1/5). The cradle circular saw with tilting table
can be easily moved from one place to another.
Storing
Unplug the machine.
Keep any machines not being used in a dry and locked
place, inaccessible to children.
When the machine is to be stored for a long time, please
follow these instructions to extend the saw life and make
its operating easy:
• Clean the saw thoroughly.
• Treat all moving parts with environment-friendly oil.
Never use any grease!
Failures – causes - remedies
CAUTION: Unplug the saw before any work on it!
Failure Causes Remedy
After plugging and
pressing the switch
the machine
switches
immediately off
(switch not remaining
pressed).
No neutral
conductor in
the system
Have the problem
removed by a qualified
electrician.
Caution:
Switch button blocking
so that you could work
even without the
neutral conductor will
shortly be removed by
the switch.
We do not take any
responsibility in
such a case.
Machine engine is
growling and not
starting.
Check the
fuses
Fuses are burnt-out -
replace them if
necessary.
Saw does not stop
when switched off.
Brake switch is
defective
Change the brake
(ask an electrician)
Inspections and servicing
Keep the cradle circular saw clean at all times. It is enough
to clean the circular saw for firewood off any sawdust using
a brush or cleaning cloth after you have finished cutting
and the circular-saw blade is idle and the power supply
interrupted.
When the machine is put out of operation for a long time,
we recommend treating the circular-saw blade and tension
spring with a cloth dipped in oil to prevent it from corrosion.
Cover the saw for cutting firewood with a sheet if standing
in exposed spaces or outdoors. Prevent especially the
engine and the switch against water.
Important instructions for sawdust container
cleaning
Remains of bark or wood may get deposited on the
security bars of the sawdust container, depending on
quality of wood. Therefore, the sawdust container must be
cleaned at regular intervals.
Safety instructions for inspections and servicing
Before any saw servicing, power supply must always be
interrupted (machine unplugged) and it needs to be made
sure the saw will not get switched on.
Only a regularly serviced and treated machine may be a
satisfactory aid. Inappropriate servicing and maintenance
may lead to unforeseen accident and injuries.
Optional supply
Hard-metal circular-saw blade for wood
Ø 700 mm/drilling 30 mm/42 teeth
Art. No. 01860
Circular-saw blade for firewood
Ø 700 mm/drilling 30 mm/56 teeth
Art. No. 01856
14
… 14 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Gude Pro PRS 700 75772 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info