Bedienungsanleitung Gude PROFI- S - 40140 (Seite 9 von 58) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Schwedisch)

622092

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

Storage

Always disconnect all pneumatic appliances if not used.

Always store the appliance at a dry place.

Assembly and first putting into operation (pic. III)

After unpacking, the appliance needs to be carefully

inspected for possible damage at transport. It is also

necessary to unconditionally ensure that all screws,

connections, etc. were tightened.

Mix and dilute the colour according to producer's

instructions. Most of the colours can be processed better

when correspondingly diluted.

Before processing, it is recommended to re-filter the

colour.

Fill the container to ¾.

Do not exceed in any case the maximum pressure

of the gun or other system components for compression!

Ensure that the vacuum container was correctly closed

and the air hose firmly connected to the gun.

Prepare a piece of cardboard that you can use during

adjustment.

Never aim the gun at other persons or yourself,

failing which there can be serious injuries.

Connect the gun now (see pic. III) to the compressed air

source.

Upon compressor switching on, check the substance

density, aim the gun at the cardboard and trigger the

starter several times. If the material is too dense, add

some solvent and proceed very carefully and do not

deviate from the substance density recommended by the

producer.

Setting (pic. I) + (pic. II)

The spraying shape, outlet volume and general appearance

of the colour layer can be set as follows.

A round or elliptical spraying shape can be reached by

turning on the air volume controller (2).

The outlet colour volume reduces on the colour volume

controller (3) by turning rightwards. Turning leftwards

increases the squirted liquid volume.

The air volume reduces on the air pressure controller (6) by

turning rightwards and increases by turning leftwards.

(pic. II)

• K spray is wrong.

The layer thickness does not differ much at

swinging.

• L spray is correct.

Always apply evenly “wet spraying to wet“

• Optimum spray can be reached at a distance

of app. 15-20 cm. A too small distance and too

fast or too slow motions result in wrong spray.

Tip: Take a piece of cardboard and make test spraying

before each work.

Maintenance and treatment

Disconnect the appliance from compressed air

source at maintenance and treatment.

Clean and treat the gun immediately

after varnishing with a

maximum care. A cleaned gun guarantees trouble-free

handling at another use. If the nozzle is removed at cleaning,

the thread and seal must be treated with light fat. That will

prevent nozzle “biting in“.

Attention: Do not put

the entire gun to a bath with solvent.

The nozzle and nozzle needle are quickly-worn parts,

therefore you should always have a set of spare nozzles with

you.

Store the pneumatic tools/appliances in dry rooms only.

Only a regularly maintained and treated appliance can serve

as a satisfactory aid. Insufficient maintenance and care can

lead to unforeseen accidents and injuries.

Failure removal

Failure Cause Removal

Gun does not

spray

1. Blocked/stic

nozzle/nozzl

e needle.

2. Faulty

nozzle/nozzl

e needle.

3. Blocked/

sticky colour

container.

1. Clean the

nozzle/nozzle needle.

2. Replace the

nozzle/nozzle needle.

3. Clean or replace the

container.

Appliance

not supplied

with

compressed

air

1. Jammed,

broken or

faulty

pneumatic

hose.

1. Check the pneumatic

hose and replace it

when faulty.

Piston does

not return to

full, stroke

with no load

1. Appliance

applied too

weakly or

too shortly.

2. Piston drags

as it is not

lubricated.

3. O-ring faulty

1. Apply the appliance

more strongly.

2. Lubricate the cylinder

guide surface.

3. Replace the O-ring.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude PROFI- S - 40140 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info