Bedienungsanleitung Gude SET 510 00909 (Seite 10 von 31) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

627511

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

Caution!

It is for your personal safety to use accessories and additions

shown in the operating manual or recommended or listed by

the manufacturer.

Use of additions and accessories other than recommended in

the operating manual or a catalogue may present a risk of

injury to you or other persons.

Repairs by Expert Electrical Engineer Only

This electrical tool conforms to respective safety provisions. .

Repairs are allowed to be done by expert workers only,

otherwise a risk of injury arises for the operator.

Operator Requirements

The operator shall read the instruction manual carefully before

using the unit.

Qualification

No special qualification is required for use of the unit except for

detailed direction by a professional.

Minimum Age

Only persons above 16 years of age are allowed to work with

the unit.

Exempted from the provision is the use of the juvenile trainees

if they work in the course of their professional training with an

aim to obtain the skill under a trainer supervision.

Training

Use of the unit requires adequate lesson by a professional

or the use of the manual only. Special training is not

required.

Disposal

The disposal instructions are derived from picture graphs

placed on the unit or packaging. Description of meaning of

individual symbols is to be found in chapter “Symbols on unit“.

Noise

- The noise of this electrical tool is measured according to ISO

3744, NFS 31-031 (2000/14 EG). Noise on the site must not

exceed 85 dB (A). If that is the case, the operators need the

noise protection equipment.

Electrical Connection to Mains

The unit may be operated on single phase a/c of

alternating voltage 230 V 50 Hz. There is protection

insulation on the unit and therefore, it may be

connected to sockets without protection connectors.

Before putting it in operation, be sure that the system

voltage conforms with the operating voltage shown

on the plate showing the unit performance data.

Initial Operation

Caution! These hedge scissors are intended for cutting

hedges, shrubbery and decorative bushes.

Any other use not expressly stated in this manual may cause a

severe damage of the scissors and present a severe risk to the

user. The hedge scissors have a two-hand operated safety

switch fitted. The hedge scissors work only if the switch button

on the guiding handle with one hand (Fig. 1/pos. 3) a while the

other hand pushes the switch on the handle (Fig. 1/ pos. 4)

If one of the switches is stopped, the cutting blades will stop.

Be careful about the cutting blades landing run.

• Test the cutting blades function. Two side cutting blades

go contrary and ensure a high cutting performance and

easy run.

• Before the use, attach the extension cable by hanging it

in the cable holder (see Fig.1/pos. 5).

Use the cables approved for use outdoors.

• Branches larger than 14 mm in diameter should by cut off

with branch shears first.

• Trapezoid cut corresponds with the natural growth of

plant and enables hedges to thrive.

• First, it is necessary to cut side areas from bottom up.

The top surface area is than cut according to one’s own

taste in form of a roof, straight or round.

• Safety cutting strip has cutting teeth, round on the sides

and arranged with offset in order to decrease the risk of

injury. An additional protection against impact prevents an

unpleasant backlash when the tool hits against wall,

fence etc. (Fig. 4).

• If the blade is blocked with hard articles, the unit must be

switched off immediately. Unplug the unit and only then

remove it.

• Caution: Metal articles, such as wire fences, plant

supports may lead to damaging the cutting strip. .

• Always lead the cable in the direction from the working

area. Work in the direction from the socket. Therefore,

cutting unit should be settled firmly before the start of the

work.

• Periods of cutting:

- Broadleaf hedges: June and October

- Evergreen hedges: April and August

- Conifer hedges: from May as necessary

Working Instructions

• In addition to hedges, the electrical scissors may be used

for cutting shrubberies and bushes.

• The best cutting performance may be obtained by

scissors and the hedge containing angle of approximately

15° (Fig. 5).

• Two sided conflicting cutting blades make cutting in both

the directions possible (Fig. 6).

• To obtain an even height of the hedge, it is recommend to

stretch a thin string along the hedge as a direction cord

The branches beyond will be cut off (se Fig. 7).

• The side surfaces of the hedge will be cut from

down to top in arc movements (see Fig. 8).

Maintenance and Care

• Before cleaning or shutting down the unit, switch it off and

unplug.

• To have the best possible performance, it is necessary to

clean and lubricate the blades regularly. Remove the

sediment with a brush and apply light oil film (see Fig. 9)

Use Biologically Degradable Oils.

• The unit body and the plastic parts should be cleaned by

light domestic detergents and wet cloth. Do not use any

aggressive detergents or solvents.

• Protect the unit from water entry in any case.

Disposal

Caution!

The hedge electrical scissors and accessories are of various

materials, such as metal and plastic.

Defective structural parts hand over to a collection

facility for recycling.

Do not throw in a dustbin.

Ask about that in a special shop or the local

administration.

Specifications

Item nb: 00909

Access / frequency: 230V~50Hz

max. Output: 500W (P1)

Knives movements: 3000 min

-1

Tooth pitch: 20 mm

Bar Length: 510 mm

Noise: L

100 dB

Protection class II

Weight: 3 kg

Gude SET 510 00909 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info