Bedienungsanleitung Gude V 1200 T 85072 (Seite 10 von 42) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

628831

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

Emergency Action

Apply the first aid adequate to the injury and get qualified

medical assistance as quickly as possible. Protect the injured

person from more accidents and calm him/her down.

For the sake of eventual accident, in accordance with DIN

13164, a workplace has to be fitted with a first-aid kit. It is

essential to replace any used material in the first-aid kit

immediately after it has been used. If you seek help, state

the following pieces of information:

1. Accident site

2. Accident type

3. Number of injured persons

4. Injury type(s)

Assigned Use

These devices can be used to charge lead batteries typically

used in motor vehicles (petrol and diesel fuel). The type of

electrolyte may be selected freely

• The design of them includes double insulation and

therefore, no earthing wire is required. They are marked

with a visible symbol on the body.

• While the battery is being charged (cf. Section “Charging

Time”), the operation is carried out with slowly falling

charging current

• Unfit for gel batteries!

• It is recommended to check continuously that the battery

charger power id adapted to the capacity of battery to be

charged. A charge too slow may demand too much time

for charging a battery. On the other hand, a powerful unit

may damage the battery.

Overload protection (pic. 2 and 3)

They have overload protection (a safety provision to protect

the battery charger from the effects of wrong connections or

overloading).

The overload protection device is a device to protect the

battery charger against failures and mishandling. It secures

safety of the entire circuit. If the device is enabled, it is

necessary to check to see whether all the instructions have

been observed

Important Notice! Replacement fuses, the resistance

values of which are different from the plate values, may

cause material and personal damage

The fuses replacement should not be done unless the

mains cable is unplugged. We shall not be held liable, not

even for the repair if the procedure is contrary to the

requirement

Fig 1 Fig 2

A. Fuse A. Fuse

B. Fuse

Residual Electrical Hazards

1. Direct electrical contact

Defective cable one plug may cause an electrical

shock injury.

 Have the defective cables and plugs replaced at a

specialist’s. Use the unit on a connection equipped

with a current protection (FI).

2. Indirect electrical contact

A risk of injury by conductive parts with open or

defective parts of the unit

 Disconnect the unit from the source of power to

maintain it. Operate with a current protection only.

3. Insufficient Lighting of Workplace

Insufficient lighting always present a high safety

risk.

 Always provide for sufficient lighting when working

with the unit.

Disposal

Disposal instructions are illustrated in the form of pictograms

on the device or packaging. Description of the pictograms is

given in "Identification" chapter.

Disposal of transport packaging

Packaging protects the device against damage during

transport. Packaging materials are usually selected according

to their effect on environment and disposal methods and can

therefore be recycled.

Returning of the packaging back to circulation saves resources

and costs for packaging disposal.

Parts of the packaging (e.g. foil, styropor) may be dangerous

for children. Risk of suffocation!

Keep these parts of the packaging out of reach of children and

dispose as soon as possible.

Handling requirements

The operating staff must carefully read the Operating

Instructions before using the appliance.

Qualification

Apart from the detailed instruction by a professional no special

qualification is necessary for using the appliance.

Minimum age

Only persons over 16 years of age can work with the

appliance. An exception includes youngsters if they work

within their professional education the purpose of which is to

obtain knowledge supervised by a trainer.

Training

Using the appliance only requires corresponding training by a

professional or following of the Operating Instructions. No

special training is necessary.

Technical data

Connector: 230 V/50-60 Hz

Charging voltage at

start:

12/24 V

Charging current: 200 Amp.

Charging arithmetic

current:

160 Amp.

Starting current 0 V: 1500 Amp.

Starting current 1,5 V: 1000 Amp.

Max mains power: 30 kW

Min. protection: 16 Amp.

Rated capacity: 36/2500 AH

Battery start: 120-200 Ah without subpena

240 Ah mit with subpoena

Weight: 65 kg

Transportation and Storage

• If putting the unit away for a prolonged storage, it should be

cleaned thoroughly.

• Securing the device in a clean, dry place

• Protect the unit from weather effects with a tarpaulin, carton

etc.

Operation (pic. 1, 4)

pic. 4:

1: Beginning of charging

2: In the course of charging

3: End of Chargign

4: Empty

5: Half-charged

6: Fully charged

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude V 1200 T 85072 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info