Bedienungsanleitung Gude V 520 85071 (Seite 10 von 48) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Schwedisch, Norwegisch)

628830

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Commissioning

1. Check on the line voltage (230 V)

2. Connect the red-clamp cable to terminal (+12) or (+24) of

the battery charger.

3. Connect the red clamp to the positive pole (+) of the

battery.

4. Connect the black clamp to the negative pole (-) of the

battery

Note: The negative pole for 12 V or 24 V batteries. The

charger to be charged by the set charging current until

completion.

Emergency Action

Apply the first aid adequate to the injury and get qualified

medical assistance as quickly as possible. Protect the injured

person from more accidents and calm him/her down.

Assigned Use

These devices can be used to charge lead batteries typically

used in motor vehicles (petrol and diesel fuel). The type of

electrolyte may be selected freely

• Unfit for gel batteries!

• It is recommended to check continuously that the battery

charger power id adapted to the capacity of battery to be

charged. A charge too slow may demand too much time

for charging a battery. On the other hand, a powerful unit

may damage the battery.

Overload protection

They have overload protection (a safety provision to protect

the battery charger from the effects of wrong connections or

overloading).

The overload protection device is a device to protect the

battery charger against failures and mishandling. It secures

safety of the entire circuit. If the device is enabled, it is

necessary to check to see whether all the instructions have

been observed

This overloading fuse is internal and is shown on the display

as “H00“ (overloading) or “noP“ (wrong poling). The appliance

can be used again when the failure is removed.

Residual Electrical Hazards

1. Direct electrical contact

Defective cable one plug may cause an electrical

shock injury.

⇒ Have the defective cables and plugs replaced at a

specialist’s. Use the unit on a connection equipped

with a current protection (FI).

2. Indirect electrical contact

A risk of injury by conductive parts with open or

defective parts of the unit

⇒ Disconnect the unit from the source of power to

maintain it. Operate with a current protection only.

3. Insufficient Lighting of Workplace

Insufficient lighting always present a high safety

risk.

⇒ Always provide for sufficient lighting when working

with the unit.

Disposal

The disposal instructions are based on icons on the appliance

or its package..

Handling requirements

The operating staff must carefully read the Operating

Instructions before using the appliance.

Qualification

Apart from the detailed instruction by a professional no special

qualification is necessary for using the appliance.

Minimum age

Only persons over 16 years of age can work with the

appliance. An exception includes youngsters if they work

within their professional education the purpose of which is to

obtain knowledge supervised by a trainer.

Training

Using the appliance only requires corresponding training by a

professional or following of the Operating Instructions. No

special training is necessary.

Technical data

Connector: 230 V/50-60 Hz

Charging voltage at

start:

12/24 V

Charging current: 12 V/63 Amp., 24 V/63 Amp.

Charging arithmetic

current:

12 V/40 Amp., 24 V/40 Amp.

Starting current 0 V: 500 Amp.

Starting current 1,5 V: 300 Amp.

Max. input: Start: 12 V/3,2 kW, 24 V/5,5 kW

Loading: 12 V/0,6 kW, 24 V/1,1

Min. protection: 16 Amp.

Rated capacity: 36-1500 Ah

Battery start:: 45-65 Ah without subpoena

80-150 Ah with subpoena

Transportation and Storage

• If putting the unit away for a prolonged storage, it should be

cleaned thoroughly.

• Securing the device in a clean, dry place

• Protect the unit from weather effects with a tarpaulin, carton

etc.

Operation

Unplug before any adjustment and set up.

Charging a 12 V battery

1. Using the voltage mode changeover switch, select the

voltage. (pic. 1/10)

2. Always connect the black cable first, to the negative pole.

Connect the red pole cable to the positive pole.

The battery should be completely disconnected from

the vehicle before getting down to charging.

4. Plug the unit and switch over to „ON“.

5. Set the required charging current on the charging current

potentiometer. If no battery is connected, is no charging

current to the terminals on.

Tip: The best economy of charging is with 10% capacity

of the battery

Example: 88 AH battery

charging current ca 9 A max.

24-V battery charging:

Procedure same as with a 12-V battery. The voltage mode

changeover switch should be at 24 V.

• Invite only 2 identical 12 V batteries.

• Make sure that the two 12 V batteries are connected in a row

and have somewhat the same battery state (resistance

load), otherwise it can lead to problems such as to overload

one of the two batteries, etc.

Note: The V520 has an automatic charge termination

limit to achieve the charging voltage. (On screen display

"END".)

Charging Time

• The recharge time is always dependent on load from the

battery state (almost half loaded or fully discharged)

• The Shop "as a refresher" of a battery meet 2-4 hours. To

Dodgeball loading requires 8-10 hours.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude V 520 85071 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info