Bedienungsanleitung Guide EasIR-4 (Seite 4 von 28) (Englisch)

776223

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

User Manual

Introduction

This publication provides the necessary information required to safely operate the EASIRTM-4 Thermal Camera.

It is important to fully check all equipment with which you have been supplied.

The equipment should be used, maintained and serviced by suitably trained personnel, capable of carefully following

the procedures and guidelines given in this User Manual.

All User Manuals and leaflets should be read thoroughly before proceeding with operation of the equipment.

It is also advisable that all User Manuals and Instruction Leaflets supplied are kept readily available, for reference when

the equipment is in general use.

Precautions

The following precautions must be adhered to at all times and must be considered in addition to any advised

precautions issued at the relevant worksite or work area.

• Keep the EASIRTM-4 Thermal Camera steady during operation.

• Do not use the EASIRTM-4 Thermal Camera in temperature exceeding its working and storage temperature

ranges.

• Do not direct the EASIRTM-4 Thermal Camera at very high intensity radiation sources such as the sun,

carbon dioxide lasers or arc welders etc.

• Do not expose the EASIRTM-4 Thermal Camera to dust and moisture. When operating the unit near water,

ensure that the unit is adequately guarded against splashes.

• When the EASIRTM-4 Thermal Camera is not in use or is to be transported, ensure that the unit and its

accessories are stored in the protective carry case.

• Do not jam the holes or loudspeaker on the camera body.

• Do not re-switch on the camera until 15 seconds later after switching it off.

• Do not throw, knock or vibrate intensely the camera and its components in order to keep them from damage.

• Do not attempt to open the camera body, as this action will void the warranty.

• Keep the SD memory card for the exclusive use of the camera.

• During using, if move the IR camera from hot/cold place to cold/hot place, e.g. from inside/outside to

outside/inside of a air-conditioned car in winter, should power off the camera firstly and leave it in the

operation site for 20 minutes, then power on the camera for normal operation and accurate temperature

measurement. Sharp and instant ambient temperature change may cause fault temperature measurement

and even damage camera’s IR detector.

• FPA setting: to ensure accurate temperature measurement, the FPA detector was calibrated in different

temperature points--7degree, 17degree, 27degree, 37degree. When power on the camera in 0 degree for

example, after period of working the temperature of the camera (the detector) will increase gradually. And

when the internal temperature of the camera beyond 7 degree, FPA setting will take place and will last for

about 30sec, and during the FPA setting the camera will not response for any operations. If power on the

camera in a temperature about 8 degree, only when the temperature of the camera beyond 17degree, this

phenomenon will happen again. Camera will adjust FPA setting itself automatically to ensure its stable

performance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Guide EasIR-4 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Guide EasIR-4

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info