Bedienungsanleitung Gymrex GR-MG13 (Seite 5 von 21) (Deutsch, Englisch, Französisch, Italienisch, Spanisch, Polnisch)

779067

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

56 Flat washer ɸ10xɸ14 1

57 Hex nut M10x6T 3

58 Allen screw M8x36 1

59 Allen screw M6x12 1

60 Spring 1

61 Screw M5x4 4

62 Screw M4x12 5

63 Allen screw with round head

M8x40

64 Lock nut M8 2

65 Allen screw with round head

M8x16

66 Handlebar plug ɸ 25 2

67 Sensor bracket 1

68 Sensor cable 1

69 Controller 1

3.2. PREPARING FOR USE

3.2.1. APPLIANCE LOCATION

The device should always be used when positioned on an

even, stable, clean, reproof and dry surface, and be out of

the reach of children and persons with limited mental and

sensory functions. It is recommended to properly protect

the oor against possible damage (using special mats).

3.2.2. ASSEMBLING THE DEVICE

I. Attach the front stabilizer (2) to the frame (1) with

two bolts (44), two washers (45), and two nuts (46).

Install the rear stabilizer (3) in the same way.

II. Please note: The bike has levelling feet (10). To level

the bike, turn the feet (10) left or right.

III. Loosen the adjustment knob (24) and insert the seat

post (4) into the frame (1). Adjust the seat post (4) to

the desired height and tighten the adjustment knob

(24). Place the horizontal saddle support (5) on the

seat post (4). Fix the saddle (28) on the support (5),

secure the seat by tightening the knob (25).

IV. Loosen the headset (38) and insert the handlebar

stem (7) in the front of the frame (1). Then, tighten

the adjustable handle (38). Place the lower handlebar

cover (41) on the handlebar stem (7). Use two bolts

(65), two spring washers (50), two at washers (51) to

attach the handlebar (6) to the stem (7). Fasten the

upper and lower handlebar covers (41,43) with four

screws (47).

V. Attach the control unit (69) to the handlebar (6).

Connect the sensor wire (68) running from the

control unit (69) to the frame (1).

VI. Please note: When connecting the wire, the

connecting parts should be on the same side.

VII. Tighten the left pedal (20) counter clockwise and the

right pedal (22) clockwise (the pedals are marked:

„L“ left and „R“ right). Make sure that the pedals

are xed properly, according to the markings. The

crank plug (23) must be rmly xed in the crank bore,

otherwise the threads might become worn.

Please note: You can lubricate the threads before

assembling the pedals.

Please note: The pedals must be tightened very

rmly. After one week of use, tighten them again.

3.3. CONTROLLER

CONTROLLER UNIT DESCRIPTION

1. Button „RESET”

2. Button „MODE”

3. Button „SET”

4. Display

CONTROL UNIT FUNCTIONS

• MODE: Switching between functions is possible

using the „MODE“ button, continue pressing the

„MODE“ button until the appropriate function is

selected. Pressing and holding the button for 4

seconds resets the value (not applicable to ODO).

• SET: Setting values for: time, distance, calories.

Pressing and holding automatically increases the

value.

• RESET: Pressing the button resets the value.

l) Put the device on a stable, dry and at surface, taking

care to keep a minimum space of 0,6 m space around

the device.

m) It is not recommended to use the device without

prior consultation with a doctor by:

• persons with contraindications from the doctor or

feeling ill,

• persons with serious illnesses,

• people suering from diseases such as hypertension,

heart disease, atherosclerosis and cerebral vein

thrombosis,

• people suering from osteoporosis,

• people with a pacemaker or other implanted medical

device.

n) Do not use the device one hour before or one hour

after a meal as undesirable eects may occur.

o) Keep the device away from moisture and dust.

p) Only one person at a time can use the device.

q) Stop exercising when you feel tired or exhausted.

r) Do not use the equipment for therapeutic purposes.

Part

number Name Quantity

1Frame 1

2Front stabilizer 1

3Rear stabilizer 1

4 Seat post 1

5Horizontal saddle support 1

6Handlebar 1

7Handlebar stem 1

8Magnetic grip 1

9Mounting angle 1

10 Levelling feet ɸ25xM8 4

11 Plug 4

12 Inner belt cover 1

13 Drive belt 5PJ550 1

14 Bearing 2

15 Compression springs ɸ20 2

16 Wheel 1

17 Wheel axle 1

18 Belt outer cover 1

19 Left crank 9/16‘’165 1

20 Left pedal 9/16” 1

21 Right crank 9/16‘’165 1

22 Right pedal 9/16” 1

23 Crank plug 2

24 Adjustment knob M16x1,15P 1

25 Adjustment knob M8 1

26 Saddle support plug 25x50x1,5T 2

27 Saddle locking bracket 1

28 The saddle 1

29 Front belt cover 1

30 Flywheel axle ɸ12x127xM10x1P 1

31 Flywheel bearing 6001 2

32 Flywheel ɸ420 1

33 Sleeve ɸ16xɸ13x14 1

34 Brake rod cover 1

35 Brake knob 1

36 Brake cover 1

37 Transport wheel 2

38 Adjustable handle M10x1,5P 1

39 Internal insert 50x100x1,5T 1

40 Internal insert 40x80x1,5T 1

41 Lower cover 1

42 Handlebar protective cover 2

43 Top cover 1

44 Screw M8x55 4

45 Pad ɸ7 4

46 Convex nut M8 4

47 Screw ST4.2x16 10

48 Screw ST4.2x16 6

49 Outer screw M8x16 4

50 Spring washer ɸ8 6

51 Flat washer ɸ8 8

52 Clamping nut M10 1

53 Tightening bolt set 1

54 Set of pressure rollers 1

55 Hex nut M10x8T 2

LIST OF PARTS

ATTENTION! Despite the safe design of the device

and its protective features, and despite the use of

additional elements protecting the operator, there

is still a slight risk of accident or injury when using

the device. Stay alert and use common sense when

using the device.

3. USE GUIDELINES

The device is designed to simulate cycling. The product is

intended for home use only!

The user is liable for any damage resulting from

unintended use of the device.

3.1. ASSEMBLY DRAWING

ATTENTION! This product‘s view can be found on the

last pages of the operating instructions (pp. 31). ATTENTION! This product’s exploded view can be

found on the last pages of the operating instructions

(pp. 32-37).

Name Function

TIME Total exercise time

SPEED Current speed

DISTANCE Distance covered

CALORIE Calories burned

ODO Total distance (from the start of the

battery operation)

SCAN

Automatically displays the above

functions (TIME-SPEED-DISTANCE-

CALORIE-ODO)

3.4. DEVICE USE

Please note: When the device is not in use, the display will

turn o automatically after approx. 4-5 minutes.

VERTICAL ADJUSTMENT OF THE SADDLE

To adjust the saddle height, loosen the adjustment knob

(24). Adjust the vertical seat post to the desired height with

the holes aligned, then tighten the knob.

30.10.2020

Gymrex GR-MG13 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info