Bedienungsanleitung Gys GYSFLASH 30-12HF (Seite 12 von 52) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

625736

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

GYSFLASH 30-12 HF

SHOWROOM MODE

On a stationary vehicle, the GYSFLASH supplies up to 30A to test high-energy consumers (engine fan, window regulator, electronic

suspension, etc…) by supplying a steady voltage adjustable:

- 12V to 14.8V

Volatage adjustment:

It is possible to adjust the voltage in steps of 0.1V according to manufacturer’s specications.

SHOWROOM MODE CONFIGURATION

12.0V

12.1V

...

14.8V

SHOWROOM

U=13.5V

12V

SHOWROOM

U=13.7V

12V

Start up with battery :

• Connect the clamps : red to the (+) and

black to the (-) of the battery.

• Push the START/STOP key to start the

mode.

• During use the current consumed and the

instantaneous voltage are displayed.

SHOWROOM MODE START UP

SHOWROOM

U=13.5V

I=12A

U=13.5V

12V

SHOWROOM

12V

Start without battery (not recommended)

It is possible to supply power to the vehicle without a battery by pushing the START/STOP key for 3 secondes. The screen will

display "no battery" for 1 second before starting to supply the vehicle.

Warning: polarity reversal can damage vehicle electronics.

Precaution :

Before using the Showroom Mode. If the screen displays a current higher than 10A, it indicates the battery is discharged. The device

will start charging automatically. Check all electrical consumers are switched off on the vehicle. Wait until the current falls below 10A

before using any electical functions of the car.

CHANGE BATTERY MODE (OPTIONAL)

The GYSFLASH will maintain a stabilised power supply to the vehicle during battery replacement to preserve memory settings. By

default this mode is inactive and doesn’t appear in the mode list. It can be activated via the Advanced menu (see page 15).

Start up :

• Connect :

1 : Red clamp to the (+) of the battery / battery terminal, in such a way that the battery can be changed without disconnecting

the clamp.

2 : Black clamp to the vehicle chassis or earth.

• Press the START/STOP key to start the mode.

• During use, the current consumed and the instanta-

neous voltage are displayed.

• When changing the battery ensure the polarity is

correct.While exchanging the batteries, be careful

not to disconnect the charger clamps to avoid loss of

electronic data.

CHANGE BATTERY START UP

CHANGE BATTERY

U=12.9V I=26A12V

aWarning: polarity reversal can damage the vehicle electronics.

POWER SUPPLY MODE (OPTIONAL)

This mode is intended for expert users only. This mode enables the charger to be used as a stabilised power supply, with regulated

voltage and adjustable maximum current. By default this mode is inactive and doesn't appear in the mode list. It can be activated

via the Advanced menu (see page 15).

Adjustment of the voltage regulation and current limitation :

The voltage regulation can be adjusted from 2V to 30V and the maximum current from 2A to 30A. For an adjustable voltage above

16V, the maximum current can be set up to 15A:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gys GYSFLASH 30-12HF Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info