Bedienungsanleitung Gys M3 GYS AUTO (Seite 10 von 52) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

665756

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

M1 - T1 & M3 - T3 GYS AUTO

SEMI-AUTOMATIC WELDING FOR STEEL/STAINLESS STEEL (MAG MODE)(FIG 3)

These welding can weld 0.6/0.8 and 1.0mm steel and stainless steel wires (g 3A). The device is capable of working

with Ø 0.8 mm steel wire (contact tube Ø 0.8, roller Ø 0.6/0.8 and Ø 0.8/1.0). If you need to use Ø 0.6mm wire, you will

have to change the contact tube, and ensure that the reversible rollers in the wire feeder are posititioned correctly (so

that the writing that states “0.6mm” is visible when in place). For Steel or Stainless Steel, you will need to use specic

gas - Argon + CO2 (Ar + CO2). The proportion of CO2 will vary depending on usage. The gas ow in steel is between 8

and 12L / min depending on the environment and experience of the welder. For the specic requirements, seek advice

from your gas distributor.

SEMI-AUTOMATIC WELDING FOR ALUMINIUM (FIG 3)

These welding can weld 0.8 and 1mm aluminium wires (g 3B).

To weld aluminium, neutral gas “pure argon” (AR) is required. When choosing gas, ask a gas distributor for advice.

The gas ow in aluminium should be between 15 and 25 L / min depending on the environment and experience of the

welder.

Things to note when welding with Aluminium:

-Set the pressure rollers of the wire feeder on the wire at the minimum pressure so as not to pinch the wire

- Remove the capillary tube before connecting the aluminium torch

- When welding aluminium use a special aluminium torch with Teon sheath to reduce friction. Do not cut the sheath

near the connector! It is used to guide the wire from the rollers. (diagram 3-B )

- Contact Tip: Use a contact tip SPECIAL aluminium corresponding to the diameter of the wire.

- Contact Tip: Use the specic Aluminium contact tip corresponding to the diameter of the wire.

SEMI-AUTOMATIC BRAZING WELDING FOR HIGH-TENSILE STRENGTH STEELS

These welding are recommended by car manufacturers to braze-weld high-tensile strength plates with a cuprosilicium

CusI3 wire or cuproaluminium CuAl8 wire (Ø 0.8 mm and Ø 1 mm). The welder must use a neutral gas: pure argon (Ar).

For specic gas requirements, seek advice from your gas distributor. The gas ow required s between 15 and 25 L / min.

GAS CONNECTION (FIG 2)

Connect the manometer (owmeter) to the gas bottle (manometer not supplied with the product).For use with one

or two bottles of gas.

To connect two bottles of gas to three torches, split the pipe into 3 pieces and attach a 3-way “Y” connector. (g 2-C )

To link a single bottle of gas with 3 torches, cut the pipe into 4 pieces and attach two 3-way “Y” connectors.

Connect each bottle to the solenoid valves in the following order:

-T1 solenoid valve to the top left (g 2B:13)

-Spool gun solenoid to the top right (g 2B:17)

-T3 solenoid valve to the bottom (g 2B:16)

To avoid any gas leaks, always use the collars supplied with the product.

PROCESS OF REELS AND TORCHES ASSEMBLY (FIG 4)

Open the device trapdoor.

- Place the reel on the driving pin (g 4:2) of the reel support.

- Adjust the reel brake (g 4:3) to avoid the reel inertia tangling the wire when welding stops. In general, do not tighten

too much!

- The electrical roller (g 4:4) is a double groove roller (0,6/ 0,8 and 0,8/1). The indication on the visible side of the

roller is the diameter in use. For a 0,8 wire, use the 0,8 groove.

- For the rst use:

- Release the xing screw of the wire guide.

To set the adjusting knob of the pressing rollers (g 4:5), proceed as follow: loosen the knob fully, start the motor by

pressing the torch trigger, tighten the adjustment knob whilst pressing the trigger. Bend the wire where it comes out of

the nozzle and hold it in place to stop its progress. The setting is correct when the guide roller slides over the wire even

when it is blocked at the end of the torch. A common adjustment is the rollers command (g 4:5) on the scale 3 for steel

and 2 for aluminium.Nb: for the aluminium wire put a minimum pressure in order not to crush the wire.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gys M3 GYS AUTO Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info