Bedienungsanleitung Gys MAGYS 400-4 (Seite 11 von 62) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

665817

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

MAGYS 400-4 / 400 GR / 500 GR / 500 WS

This manual contains safety and operating instructions. Read it carefully before using the device for the rst time and

keep it in a safe place for future reference.

GENERAL DESCRIPTION

Thank you for choosing this GYS product; please read this instruction manual carefully before installing and using the

product, and keep in a safe place for future reference.

The MAGYS are ventilated semi-automatic welding units (MIG or MAG). Adjustment is quick and easy with their « syner-

gic wire speed » function. They work on a 400V three-phase power supply.

In order to function MAGYS:

• 400 GR requires separate wire feeder WS-4R (ref. 034723) or W5S-4L (ref 032835) and a connection cable.

• 500 GR requires separate wire feeder WS-4R (ref. 034723) or W5S-4L (ref 032835) and a connection cable.

• 500 WS requires separate wire feeder WS-4L (ref. 033573) or W5S-4L (ref 032835) and a connection cable.

ELECTRICITY SUPPLY

The absorbed current (I1eff) is indicated on the device, for use at maximum settings. Check that the power supply and

its protection (fuse and/or circuit breaker) are compatible with the current needed during use.

The device must be placed in such way that the power socket is always accessible.

Do not use an extension cord which has a wire section smaller than 4 mm².

These units are supplied with a 32A plug type EEC7/7. They should be plugged in to a 400 V (3PH) power socket WITH

earth and protected by a circuit breaker (32A and 1 differential 30Ma.)

DEVICE PRESENTATION

Put the rubber mat (only for the Magys 400-4) and the four ring eyes (with their lock washers). The gas bottle needs to

be fastened with 2 chains in the holes at the back of the machine. Attention: Fasten correctly the bottle. You have also

holes to pass a strap on (not included).

1 - On – Off switch 8 - Fastening chains for bottles

2 - Power settings – 2 switches with 9 positions to adjust

the welding voltage output

9 - Reel support Ø 200/300 mm.

3 - Control panel – Welding settings

10 - Gas connector (For the Magys 500 WS, the gas hose

needs to be connected to the owmeter of the bottle).

4 - European standard torch connection

11 - Rear panel for the connection of the separate wire

feeder (Magys 400 GR/500 GR/500 WS)

5 - Power cable (5m) 12 - 5.5 L tank (Magys 500 WS)

6 - Earth cable

13 - Chain xing slot

7 - Gas bottle support (max 1 bottle of 10m3)

SEMI-AUTOMATIC WELDING FOR STEEL / STAINLESS STEEL (MAG MODE) (FIG. 2-A)

The MAGYS units are equipped originally to work on 1mm steel wire (original drive rollers Ø 1/1.2 steel/stainless steel).

Make sure that drive rollers, liner and contact tube are adapted to your wire diameter.

For Steel or Stainless Steel, you will need to use specic gas - Argon + CO2 (Ar + CO2). The proportion of CO2 will vary

depending on usage. The gas ow for steel is between 15 and 25L / min depending on the environment and experience

of the welder.

SEMI-AUTOMATIC WELDING FOR ALUMINIUM (MIG MODE) (FIG. 2-B)

This welding unit can weld aluminium wires from 1mm.

To weld aluminium, neutral gas “pure Argon” (AR) is required. When choosing gas, ask a gas distributor for advice.

The gas ow in aluminium should be between 20 and 25 L / min depending on the environment and experience of the

welder.

Things to note when welding with Aluminium

- Set the pressure of the rollers to a minimum so as not to crush the wire

- Remove the capillary tube before connecting the aluminium torch

- When welding aluminium use a special aluminium torch with Teon sheath to reduce friction.

Do not cut the sheath near the connector! It is used to guide the wire from the rollers.

(See diagram (16))

- Contact Tip: Use the specic Aluminium contact tip corresponding to the diameter of the wire.

- Drive rollers: Use specic drive rollers to weld with aluminium wire.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gys MAGYS 400-4 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info