Bedienungsanleitung Gys MAGYS 400 GR (Seite 16 von 62) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

665818

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

MAGYS 400-4 / 400 GR / 500 GR / 500 WS

SAFETY

Arc welding can be dangerous and can cause serious and even fatal injuries.

Protect yourself and others. Ensure the following safety precautions are taken:

Handling

Unplug the unit, check if the chains of the gas bottle are fastened enough, don’t ride over the

wires and cables. In compliance with the EN60974-1 standard, don’t tilt the unit more than 15°

when you move or set up the welding unit.

Lifting

• Systematically remove the gas bottle. Do not lift the unit with any other charge.

• Use simultaneously the four ring eyes being sure that the weight is well distributed and the

angle between the strap and the machine is at a minimum of 60°. Do not lift the welding unit

with the handles.

• Use only the link chains or straps with the correct size and the same width. The hooks need to be

locked in compliance with the standard DIN 82101, shape A, minimum size 0.4. The weight with

equipment of the MAGYS 400-4S is around 160kg, the MAGYS 400 GR equipped weighs around

210 kg and around 220kg for the MAGYS 500 GR/500 WS.

Fuses (x2)

The low voltage circuit of the unit is pro-

tected by 2 fuses (T2A) located on the

circuit board of the generator.

Arc radiation: Protect yourself with a helmet tted with lters in compliance with EN169 or EN 379

Rain, steam, damp

Use your welding unit in a clean/dry environment (pollution factor ≤ 3), on a at surface, and

more than one meter from the welding work-piece. Do not use in rain or snow.

Electrical shock:

This device must only be used with an earthed power supply. Do not touch the parts under high

voltage. Check that the power supply is suitable for this unit

Falls: Do not place/carry the unit over people or objects.

Burns: Wear protective (re-proof) clothing (cotton, overalls or jeans).

Fire risks: Remove all ammable products from the work area. Do not work in presence of ammable gases

Fumes:

Do not inhale welding gases and fumes. Use the device in a well ventilated environment, with

articial extraction if welding indoors.

Additional precautions:

Avoid any welding operation undertaken in:

• rooms where there is an increased risk of electric shocks,

• Poorly ventilated rooms,

• In the presence of ammable or explosive material,

Use should always be approved by a «responsible expert», and made in presence of people trai-

ned to intervene in case of emergency.

Technical protection as described in the Technical Specication CEI/IEC 62081 must be imple-

mented. Welding in raised positions should not be undertaken, except in case of safety platforms

use.

People wearing Pacemakers are advised to see their doctor before using this device.

Do not use the welding unit to unfreeze pipes.

Handle gas bottles with care - there is increased danger if the bottle or its valve are damaged.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gys MAGYS 400 GR Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info