665831

Gys NOMADFEED 425-4 Seite 11

11
Zoom out
Zoom in
Vorherige Seite
1/68
Nächste Seite
11
NOMADFEED
EN
Caution, welding in small spaces requires surveillance from a safe distance. In addition, the welding of certain materials containing lead, cadmium,
zinc, mercury or beryllium may be very harmful. Also remove any grease on the metal pieces before welding. Gas cylinders must be stored in an open
or ventilated area. The cylinders must be in a vertical position and fastened to a support or trolley.
Do not weld in areas where grease or paint are stored.
FIRE AND EXPLOSION HAZARDS
Protect the entire welding area. Compressed gas containers and other ammable materials must be moved to a minimum safe
distance of 11 meters.
A re extinguisher must be readily available near the welding operations.
Be careful of spatter and sparks, even through cracks. It can be the source of a re or an explosion.
Keep people, ammable objects and pressurised ontainers at a safe distance.
Welding of sealed containers or closed pipes should be avoided, and when opened, the operator must remove any inammable or explosive materials
(oil, petrol, gas...).
Grinding operations should not be directed towards the device itself, the power supply or any ammable materials.
GAS BOTTLE
Gas leaking from the bottles can lead to suffocation if present in high concentrations around the work area.
Transport must be done safely: bottles closed and welding machine switched off. Always keep cylinders in an upright position
securely fastened to a xed support to reduce the risk of falling.
Close the bottle between two operations. Be wary of temperature changes or exposure to sunlight.
The bottle must not be in contact with a ame, an electric arc, a torch, an earth clamp or all other sources of heat.
Always keep gas bottles at a safe distance from electrical circuits and thus never weld a pressurised bottle.
Be careful when opening the valve on the gas bottle, it is necessary to remove the tip of the valve and make sure the gas meets your welding
requirements.
ELECTRICAL SAFETY
The machine must be connected to an earthed electrical supply. Use the fuse size recommended on the signage table.
An electrical discharge can directly or indirectly cause serious and potentially deadly incidents.
Do not touch any live part of the machine (inside or outside) when it is plugged in (Torches, earth cable, cables, electrodes) because they are
connected to the welding circuit.
Before opening the device, it is imperative to disconnect it from the mains and wait 2 minutes, so that all the capacitors are discharged.
Do not touch the torch or electrode holder and earth clamp at the same time.
Damaged cables and torches must be changed by a qualied professional.
Make sure that the cable cross section is adequate with the usage (extensions and welding cables).
Always wear dry clothes in good condition, in order to be insulated from the electrical circuit. Wear insulating shoes, regardless of the environment
in which you work in.
Risk of electrocution !
If the weld is performed using different processes while the torch and the electrode holder are connected to material, a no-load
voltage or welding voltage is applied to the circuits !
At the beginning of a job and during interruptions, always isolate the torch and the electrode holder !
Isolation of the welder at the arc in relation to the welding voltage !
Not all the different parts involved in the welding current can be protected against direct human contact. The welder must
therefore avoid the risks by following the relevant safety regulations. Even a contact at low current may take the operator by
surprise and cause an incident.
• Make sure protective wear used is dry and in good condition (rubber sole shoes / leather welding gloves without staples or
rivets) !
• Avoid contact with with exposed electrical wire and non-insulated plugs!
• Always leave the welding torch or the electrode holder on an insulated surface !
Risk of burn as the welding current goes from the machine into the cables !
If the connectors are not safely locked in place, the connectors and the cables can become hot and cause burns !
• Check the welding connectors daily and lock them in place if needed by turning them to the right.
Stray welding currents can damage earth connections, damage electrical equipment or cause components to overheat and cause
re.
… 11 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Gys NOMADFEED 425-4 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info