Bedienungsanleitung Gys PROMIG 400-4S DUO DV (Seite 12 von 64) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

665816

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

PROMIG

Stray welding currents/voltages may destroy earth conductors, damage electrical equipment or cause components to warm up which

may cause a re.

- All welding connections must be rmly secured, check regularly !

- Check that the metal piece xation is strong and without any electrical problems !

- Attach or hang all the electrically conductive elements,such as the trolley in order to insulate them

- Do not place any electrical equipment such as drills on top of the welding machine without insulating them !

- Always place welding torches or electrodes holders on an insulated surface when they’re not in use !

EQUIPMENT INSTALLATION

• Put the machine on the oor (maximum incline of 10°.)

• Ensure the work area has sufcient ventillation for welding, and that there is easy access to the control panel.

• The machine must not be used in an area with conductive metal dusts.

• The machine must be placed in a sheltered area away from rain or direct sunlight.

• The machine protection level is IP21, which means :

- Protection against acess to dangerous parts from solid bodies of a ≥12.5mm diameter and,

- Protection against vertically falling drops.

The power cables, extensions and welding cables must be fully uncoiled to prevent overheating.

The manufacturer does not incur any responsability regarding damages to both objects and persons that result from an incorrect

and/or dangerous use of the machine.

MAINTENANCE / RECOMMENDATIONS

• Maintenance should only be carried out by a qualied person. Annual maintenance is recommended.

• Ensure the machine is unplugged from the mains, and wait for two minutes before carrying out maintenance work.

DANGER High Voltage and Currents inside the machine.

• Remove the casing 2 or 3 times a year to remove any excess dust. Take this opportunity to have the electrical connections

checked by a qualied person, with an insulated tool.

• Regularly check the condition of the power supply cable. If the power cable is damaged, it must be replaced by the

manufacturer, its after sales service or an equally qualied person.

• Ensure the ventilation holes of the device are not blocked to allow adequate air circulation.

• Do not use this equipment to thaw pipes, to charge batteries, or to start any engine.

INSTALLATION (FIG-I)

– PRODUCT OPERATION

DESCRIPTION

In order to get the maximum from this machine, please read the following instructions:

The Promig is a «synergic» semi-automatic welding unit, for welding (MIG or MAG). It is recommended for welding steel, stainless

steel and aluminium. Adjustment is quick and easy with the « synergic wire speed » function. It works on 3-phase 400V (or on

230V - 3 phase for the DV models as well.)

POWER SUPPLY

The welders are tted with a 32 A socket type EN 60309-1 which must be connected to a three-phase 400V (50 - 60 Hz) power

supply tted with four wires and one earthed neutral. The absorbed effective current (I1eff) is displayed on the machine, for optimal

use. Check that the power supply and its protection (fuse and/or circuit breaker) are compatible with the current needed by the

machine. In some countries, it may be necessary to change the plug to allow the use at maximum settings.

Power supply 3-phase 230V for the Promig 400 G DV and 400 DUO DV :

WARNING: these devices are pre-assembled at the factory on 3-phase 400V. If your electrical

installation is on 3-phase 230V amend the connections on the terminal block inside the product.

This operation must be done by a qualied person. Please see the electrical diagram 230V

located inside the product. The power supply must be protected by a 25A circuit breaker and a

30mA differential.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gys PROMIG 400-4S DUO DV Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info